background image

ASSEMBLY INSTRUCTIONS

ASSEMBLY TIPS:

1 . Remove hardware from box and sort by size.

2 . Please check to see that all hardware and parts are present prior to start of assembly.
3 . Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.

Warning !

1 . Don't attempt to repair or modify parts that are broken or defective. Please contact the

     store immediately.
2 . This product is for home use only and not intended for commercial establishment.

PARTS IDENTIFICATION

www.coastercompany.com

BED RAIL

2PCS

BED SLAT WITH 3 HOLES

3PCS

G

B1 (BOX 1)

A

HEADBOARD PANEL

1PC

C

LEFT HEADBOARD LEG

1PC

PAGE 2 OF 6

B

RIGHT HEADBOARD LEG

1PC

F

R

D

FOOTBOARD

1PC

ROLL SLAT (5PCS)

H

CENTER RAIL

I

2SETS

1PC

DRAWER BOTTOM
TRESTLE BAR

1PC

J

BED SLAT SUPPORT
WITH LEVELER

L

DRAWER BOTTOM
TRESTLE BAR SUPPORT
WITH LEVELER

M

3PCS

B2 (BOX 2)

B3 (BOX 3)

1PC

FOOTBOARD
DRAWER  BOX

O

2PCS

203481KE (B1)
HEADBOARD COMPLETE

*FROM BOX 1

HB

203481KE (B1)
FOOTBOARD

*FROM BOX 1

1PC

1PC

D

E

CONCEAL PANEL

1PC

ITEM  :

  

203481KE (B1 ~ B3)

BOTTOM CROSS BAR

2PCS

K

UPPER TRESTLE

SUPPORT BAR

N

1PC

Summary of Contents for 203481KE







Reviews: