background image

BATTERY
DOOR ON
HANDSET

To Dispose Of Your Battery

The rechargeable nickel-cadmium (NiCad)
battery in this product must be recycled or
disposed of properly in compliance with all
applicable laws. Certain states or
municipalities require recycling and have
established collection programs. Please
contact your local waste removal authority
for instruction or return to Cobra for
recycling. Wrap carefully and mail postage
prepaid to:

COBRA ELECTRONICS

CORPORATION

6500 W. Cortland Street

Chicago, Il. 60707

Attn: Battery Recycling

Do not put batteries into fire or
expose to high heat. They may
explode.

“Contains Nickel-Cadmium
rechargeable batteries. Must be
recycled or disposed of properly”.

Your Cobra Intenna  Cordless Telephone
Answering System comes complete with a
rechargeable nickel-cadmium battery
already in the handset. You will need to
charge the battery by plugging in the base,
placing the handset in the base and letting it
charge overnight (at least 12 hours).

Battery Recharging

There are three things that can happen to
indicate that your handset battery needs
recharging. When one of these three things
occurs, you will need to return the handset
to the base and recharge for at least 12
continuous hours.

1. The TALK Button on the handset
flashes.

2. A 2-beep warning sounds while you
are using the phone. This indicates that
you have just a few minutes of power
left to complete your conversation
before the phone disconnects.

3. The handset beeps at 30 second
intervals for five minutes when it has
been away from the base too long.
After five minutes, it will not flash or
beep, nor will you be able to get a dial
tone. Return the handset to the base
for recharging.

NOTE: To prevent your batteries from
running out of power, Cobra suggests that
you leave the handset in the base as much
as possible when not in use. The CHARGE
indicator will remain on as long as the
handset is in the base, even after the
batteries are fully recharged. This will not
damage the batteries.

Replacing The Battery

Your phone uses a Ni-Cad battery which can
lose its ability to take a charge after several
hundred hours of use. If you notice a
shorter talk time after charging, your battery
may need replacing.
If you have recharged the battery for 12
hours or more and the handset does not
work when the TALK button is pressed, you
may need to replace the battery. To order a
new battery, call Cobra toll-free at 1-773-
889-3087, or remove it from the handset
and take it to a local hardware store or
home center store to be certain that you
are getting the proper replacement battery. 

To Remove/Replace
The Handset Battery 

1. To remove the battery door, press and
slide downward.
2. Carefully disconnect the battery pack
and dispose of it properly. See
BATTERY DISPOSAL below.
3. To replace, connect the new battery
and replace the door.  Return the
handset to the base and charge the
battery  overnight (at least 12 hours).

To Clean The
Charging Contacts

The two metal charging contacts on both
the handset and the base should be
cleaned regularly with a soft, dry cloth for
optimum recharging performance.

2

1-773-889-3087

NEED HELP

?

RECHARGEABLE BATTERY INFORMATION

Ni-Cd

RBRC

RBRC

1

1

AN8630-25

Cobra

®

Summary of Contents for antenna AN - 8630 - 25

















Reviews: