background image

7

5.8 GHz Dual-Input Audio/Video Sender System - AVS58

www.cocoonsystems.com.au

5.2 C

onnECtInG

 

VIA

 SCARt C

onnECtIon

 (

ADAptER

 

lAbElED

 “

tRAnSmIttER

”)

If your source device has a SCART output then this can be used for connection to the 

Transmitter.  Connect one of the supplied AV cables to a spare input on the Transmitter 

(labelled AUDIO IN - VIDEO IN or AV IN).  Next, plug the red/white/yellow plugs from the 

other end of the AV cable into one of the supplied SCART adaptors labelled “Transmitter”. 

Next, connect the SCART adaptor into the SCART output of your source device. If you 

don’t have a spare SCART output on your source device because it is connected to the 

local TV, you may remove this connection as the Transmitter has an output for connection 

to the local TV (see 5.4 below).

Important:

 The AV IN terminals on the Transmitter should only be connected to an AV 

Output on your source device, it will not work if connected to an AV Input.

If you want to transmit audio only, connect only the white and red plugs of the AV cable to 

the SCART adaptor. 

5.3 C

onnECtInG

 

to

 

A

 3.5

mm

 A

UDIo

 J

ACk

 (

HEADpHonE

 

SoCkEt

)

You can connect the Transmitter to a 3.5mm audio jack (headphone socket) of a source 

device to transmit audio only (eg. to transmit audio from a stereo or personal music player).  

To do so, first connect one of the supplied AV cables to an input on the Transmitter (labelled 

AUDIO IN - VIDEO IN or AV IN), then plug just the white and red plugs into the audio adap-

tor. Next connect the audio adaptor to the 3.5mm audio output jack of your source device.

5.4 C

onnECtInG

 

tHE

 t

RAnSmIttER

 

to

 

tHE

 l

oCAl

 tV

In order to view signals from your source device(s) on the local TV (where the Transmitter is 

situated), plug a supplied AV cable into this connection and plug the red/white/yellow plugs 

from the other end into an AV Input on your TV.  You can use the Source Selector Switch 

on the rear of the Transmitter to choose which signal (Source 1 or Source 2) is transmitted 

to the TV connected to the A/V OUT output (see page 9 - Fig. 5.8.2).

5.5 I

nfRARED

 E

xtEnDER

 (

foR

 

REmotE

 

ContRol

 

of

 

SoURCE

 

DEVICES

 

fRom

 

REmotE

 

Room

)

To enable remote control of the source device(s) from the remote location (where you will 

have the Receiver installed), you have to connect the IR Extender lead. The Transmitter 

outputs the IR signal (sent from the Receiver) through the 3 stick-on IR emitter diodes 

positioned on the IR Extender lead.  The emitters output the IR signal directly onto the IR 

receiving sensor of your source device(s) (see page 9 - Fig. 5.8.3).

Connect the 3.5mm plug of the IR Extender to the IR EXT. socket on the Transmitter. Next, 

stick one of the IR emitters next to the IR receiver sensor window of the device you want to 

control. Information on where the IR sensor window is located should be in the manual of 

your device.  Further tips are provided in the troubleshooting section (pages 14-15).

Summary of Contents for AVS58

















Reviews: