Coda 07X Operation Manual Download

Page: 6 / 14

The 07X can be operated by remote control. The MX-

350 Learning Remote is included with the preamp. The

relevant pages of the remote interface are described

below. For instructions on using the MX-350 itself see the

manual included with the remote.

The five buttons to the right of the LCD are used to select

the functions shown in the display window. Select [07X]

to control the 07X.

VOL

Changes audio level

MUTE

Mutes the amplifier

ON / OFF

Turns bias on and off

PAGE

Cycles through available

remote commands.

BAL/1 BAL/2 DISC AUX

Selects audio input.

PROC

Toggles processor loop

MONO

Combines channels

HT BY

Toggles bypass mode

BAL <>

Selects balance control

GENERAL CONTROLS

07X PAGE 1

07X PAGE 2

OFF

MAIN

VOL

MUTE

GUIDE

OFF

MAIN

VOL

MUTE

GUIDE

OFF

MAIN

VOL

MUTE

GUIDE

CODA

CO 07

CABLE

CSI/B

CO 07

CO CP

BAL/1

BAL/2

DISC

AUX

PROC

DETAILED INSTALLATION

MONO

HT BY

BAL <>

MUTE

Mutes audio

5 of 5

1 of 5

1 of 2

CO 07

Summary of Contents for 07X















Search results

Summary of Contents for 07X

Reviews:

Related manuals for 07X

Brands by name

Popular brands

Coda 07X, Operation Manual

Search results

Summary of Contents for 07X

Reviews:

Related manuals for 07X

Brands by name

Popular brands