background image

8

Flash Patterns (including for those beacons with task light option):

PATTERN NO.

PATTERNS

SYNCHRONIZE

1

NFPA Quad Phase 0

YES

2

Cycle Flash 75fpm Phase 0

YES

3

Quad 75fpm Phase 0

YES

4

Triple 75fpm Phase 0

YES

5

Double 75fpm Phase 0

YES

6

Single 75fpm Phase 0

YES

7

Variable Single Flash Phase 0

YES

8

Rotate 75rpm

Simultaneous Only

9

NFPA Quad Phase 1

YES

10

Cycle Flash 75fpm Phase 1

YES

11

Quad 75fpm Phase 1

YES

12

Triple 75fpm Phase 1

YES

13

Double 75fpm Phase 1

YES

14

Single 75fpm Phase 1

YES

15

Variable Single Flash Phase 1

YES

16

Cycle Flash 150fpm Phase 0

YES

17

Quad 150fpm Phase 0

YES

18

Triple 150fpm Phase 0

YES

19

Double 150fpm Phase 0

YES

20

Single 150fpm Phase 0

YES

21

Single 250fpm Phase 0

YES

22

Single 375fpm Phase 0

YES

23

Rotate 150rpm

Simultaneous Only

24

Cycle Flash 150fpm Phase 1

YES

25

Quad 150fpm Phase 1

YES

26

Triple 150fpm Phase 1

YES

27

Double 150fpm Phase 1

YES

28

Single 150fpm Phase 1

YES

29

Single 250fpm Phase 1

YES

30

Single 375fpm Phase 1

YES

31

NFPA Quad Alternating

Simultaneous Only

32

Cycle Flash 75fpm Alternating

Simultaneous Only

33

Quad 75fpm Alternating

Simultaneous Only

34

Triple 75fpm Alternating

Simultaneous Only

35

Double 75fpm Alternating

Simultaneous Only

26

Single 75fpm Alternating

Simultaneous Only

37

Cycle Flash 150fpm Alternating

Simultaneous Only

38

Quad 150fpm Alternating

Simultaneous Only

39

Triple 150fpm Alternating

Simultaneous Only

40

Double 150fpm Alternating

Simultaneous Only

41

Single 150fpm Alternating

Simultaneous Only

42

Single 250fpm Alternating

Simultaneous Only

43

Single 375fpm Alternating

Simultaneous Only

Summary of Contents for ARCH Beacon













Reviews: