Code 3 ARCH Beacon Installation & Operation Manual Download

Page: 9 / 12

Maintenance:

The beacons are designed to be maintenance free. Refer to the guide below for help with troubleshooting.

Should the unit be diagnosed as malfunctioning, remove unit and replace with a new beacon.

TROUBLESHOOTINg

Problem

Probable Cause

Remedy

Beacon does not activate

a. No power to unit

a. Check wire for loose connection

b. Power input wire reversed

b. Reverse power wires

c. Damaged or shortaged cabling

c. Check cables for damage

d. Defective beacon

d. Replace beacon module

Beacon is constantly ON (not

flashing)

a. Pattern select wire permanently

grounded or shorted to GND

a. Avoid permanent grounding of

pattern select wire

LED beacon housings may become hot with extended use. Allow beacons to cool completely

before attempting to remove.

WARNING!

Summary of Contents for ARCH Beacon













Search results

Summary of Contents for ARCH Beacon

Reviews:

Related manuals for ARCH Beacon

Brands by name

Popular brands

Code 3 ARCH Beacon, Installation & Operation Manual

Search results

Summary of Contents for ARCH Beacon

Reviews:

Related manuals for ARCH Beacon

Brands by name

Popular brands