background image

5

ca1051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.

  Using the Personal Protection Alarm (Panic)

Press and hold the 

 button for 3 seconds to activate the personal protection

alarm. During panic mode, the normal function of the transmitter buttons will be
suspended. The transmitter’s   and   buttons can be used to lock and unlock the
door (if the option is installed). To stop the alarm, press and hold the 

 button on

the transmitter again for 3 seconds. The system will automatically stop after 30
seconds.

  Car Jack Mode

This feature must be turned on in system programming, please consult your
installing dealer.

Triggering Car Jack mode: While the ignition is ON and press and hold   +   for 2
seconds, the parking lights will flash 1 time and the system will act as follows;

1.

50 seconds after being triggered the siren will chirp for 15 seconds,
during this 15 seconds you will be alerted to push the valet button to
turn off Car Jack mode. If Car Jack mode is not turned off at this time it
will advance to the next step.

2.

Following the 15 second chirps (total time now 65 seconds) the siren
will go into full sound and the parking lights will start flashing.

3.

90 seconds after trigger in, addition to the siren and parking lights, the
system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS
STATE UNTIL THE BATTERY IS DEPLETED.

OVERRIDE THE SYSTEM TO TURN OFF CAR JACK MODE: Turn the ignition OFF
then On and press the valet button within 10 seconds.

Summary of Contents for ca 1051











Reviews: