background image

10

ca2051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.

Manual Feature Programming - Feature Bank 2 & 3

1.

Turn the ignition ON.

2.

Press and hold the valet/override button.

3.

Within 10 seconds  the system will chirp (3) three times.

4.

Use the valet/override button to advance through each option bank. For
feature programming advance to Feature Bank 2 or 3, which is (4) four or
(5) five chirps.

5.

Use the transmitter 

   button to scroll through the selections in each

feature bank, the system will chirp to match the feature number.

6.

Press the transmitter   button to change the desired feature. The LED will
flash indicating the changed feature.

Set Up & Programming

Transmitter Programming - Feature Bank 1

1.

Turn the ignition ON.

2.

Press and hold the valet/override button.

3.

Within 10 seconds  the system will chirp (3) three times.

4.

Press 1 button of each transmitter you wish to program.

5.

The system will respond with 1 chirp for each accepted transmitter.

6.

Pressing the override button at anytime during programming will advance to
the next bank.

NOTE: The system will exit transmitter programming after 15 seconds of inactivity.

NOTE: This system has 1 button programming which programs all channels of the
system.

NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.

Defaulting All Features: Pressing the   button anytime while in any of the
feature banks will default all features and return you to feature bank 2 - 4 chirps.

NOTE: The system will remain in feature programming mode as long as the
ignition is on, there is no time limit. To exit programming turn the IGNITION OFF.

Summary of Contents for ca 2051

















Reviews: