background image

Using Your  Remote Transmitter

 Locking the Vehicle’s Doors

To lock the vehicle’s doors, exit the vehicle, close all doors, then press the LOCK
icon button on the transmitter.  The horn will honk and the parking lights will flash,
indicating the system has locked the doors (if equipped and connected), and
activated the starter disable feature. The status indicator (blue warning light on the
dash) will blink steadily, once per second.  To lock the vehicles doors silently, press
and hold the LOCK icon button for 1 second.  The parking lights will flash, indicating
the system has locked the doors (if equipped and connected), and activated the
starter disable feature. The status indicator (blue warning light on the dash) will blink
steadily, once per second.

 Unlocking the Vehicle’s Doors

To unlock the vehicle’s doors, press the UNLOCK icon button.  The horn will chirp and
the parking lights will flash once, and the doors will unlock (if equipped and
connected).  The interior light will turn on for 1 minute or until the ignition key is turned
on.  To unlock the vehicles doors silently, press and hold the UNLOCK icon button for
1 second.  The parking lights will flash, indicating the system has unlocked the doors
(if equipped and connected).

 Disabling/Enabling  Lock and Unlock Confirmation Chirps

1.  Turn the ignition key ON then OFF
2.  Within 10 seconds push and release the valet/override button 3 times.
3.  The horn will honk 2 times to disable horn honks or 1 time to enable horn honks.

 Two Stage Door Unlock

If this feature is enabled on your system, pressing the UNLOCK icon button one time on the transmitter
will unlock only the driver’s door.  Press the UNLOCK icon button again within 15 seconds to unlock the
remaining doors.

 Activating the Trunk Release Feature

If this feature is enabled on your system, pressing and holding the TRUNK icon button on the transmitter
for 2 seconds will open the vehicles trunk or hatch.

 Turning on the Vehicle’s Headlights

If this feature is enabled on your system, pressing and holding the LOCK icon button on the transmitter
for 3 seconds will turn on the vehicle’s headlights for 20 seconds.

 Using the Progressive Car Finder Feature

Press the      icon button on the transmitter to locate your vehicle.  The horn will honk 5 times at low
volume increasing in volume each of 3 times the button is pressed.

 Using the Personal Protection Alarm (Panic)

Press and hold the      icon button on the transmitter for 3 seconds to activate the personal protection
alarm.  The horn will pulse for 30 seconds.  Pressing any button on the transmitter will turn the personal
protection alarm off.

 Using the Transmitter Flashlight Feature

The (1) 6 button transmitter included with your system has a flashlight bulb built into the top of the
transmitter.  Pressing and holding the LIGHT icon button on the transmitter will activate the flashlight until
the button is released.

*Throughout this manual, ‘press’ refers to pressing for less than 1 second.

*

*

3

Summary of Contents for CA-535











Reviews: