background image

Regulations/Conformity

Note

: For the most current CE declaration and regulatory conformity information, see the Cognex support site:

cognex.com/support

.

Declaration of Conformity

Manufacturer

Cognex Corporation
One Vision Drive
Natick, MA 01760 USA

In-Sight Micro 1020/1050/1100/1110/1400/1410: Type 821-0043-1R
In-Sight Micro 1100C/1400C: Type 821-0044-1R
In-Sight Micro 1402/1412: Type 821-0078-1R
In-Sight Micro 1403/1413: Type 821-0047-1R
In-Sight Micro 1403C: Type 821-0048-1R
In-Sight Micro 1500: Regulatory Model 1AAN
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take immediate measures. This equipment complies with the
essential requirements of the EU Directive 2014/30/EU. Declarations are available from your local
representative.

EU RoHS

Compliant to the most recent applicable directive.

FCC

FCC Part 15, Class A
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

Korea

In-Sight Micro 1020/1050/1100/1110/1400/1410: CGX-ISM1400-00(A)
In-Sight Micro 1100C/1400C: CGX-ISM1400-C00(A)
In-Sight Micro 1402/1412: KCC-REM-CGX-ISM1402-01
In-Sight Micro 1403/1413: CGX-ISM1403-00(A)
In-Sight Micro 1403C: CGX-ISM1403-C00(A)
In-Sight Micro 1500: Regulatory Model 1AAN: MSIP-REM-CGX-1AAN
This device is certified for office use only and if used at home, there can be frequency interference
problems.

NRTL

TÜV SÜD AM SCC/NRTL OSHA Scheme for UL/CAN 60950-1.

CB

TÜV SÜD AM, IEC/EN 60950-1. CB report available upon request.

3

Regulations/Conformity

Summary of Contents for In-Sight Micro Series































Reviews: