background image

Instruction # 7055 

Cognito Motorsports 

Limited Lifetime Warranty 

Cognito Motorsports warrants, to the original retail purchaser, that its suspension products are free from defects in workmanship 
and material for as long as the purchaser owns the vehicle on which the product was originally installed.  Cognito Motorsports 
does not warrant the product for finish, alterations, modifications, and/or original installation contrary to specifications of 
Cognito Motorsports.  Cognito Motorsports suspension products are not designed nor intended to be installed on vehicles used in 
race applications or for racing purposes or for similar activities involving abnormal abuse other than the vehicle was originally 
designed to handle or endure.  (A “RACE” is defined as any contest between two or more vehicles, and/or contest of one or more 
vehicle against the clock, whether or not such contest is for a prize.)  

 This warranty is  for a one-time replacement of each Cognito Motorsports product and does not cover any part that 

Cognito Motorsports has previously replaced under this warranty. This warranty does not include coverage for police or taxi 
vehicles, race vehicles, or vehicles used for government or commercial purposes.  Also excluded from this warrant are sales 
outside of the United States of America.  Alterations to the finish of the parts including but not limited to painting, powder 
coating, plating, and/or welding will void all warranties.    Cognito Motorsports obligation under this warranty is  limited to the 
repair or replacement, at Cognito Motorsports option of the defective product.  Any and all costs of removal, installation or re-
installation, freight charges, incidental or consequential damages are expressly excluded from this warranty. 

  This warranty excludes the following items: bushings, bumpstops, tie-rod ends, limiting straps, and hiem joints.  

These parts are subject to wear and are not considered defective when worn.  They are warranted for 60 days of purchase for 
defects in workmanship.  Cognito Motorsports suspension components must be installed as a complete system.  Any substitutions 
or exemptions of required components will immediately void the warranty.  Some finish damage may happen to parts during 
shipping and is  not covered under warranty.  This warranty shall not apply to any product that had been subject to accident, 
negligence, alteration, abuse, or misuse.  Cognito Motorsports does not warrant products not manufactured by Cognito 
Motorsports. Cognito Motorsports reserves the right to supersede, discontinue, or change the design, finish, part number and/or 
application of parts when deemed necessary by Cognito Motorsports without written notice, and in the sole and absolute 
discretion of Cognito Motorsports. 

Warranty Claims 

All warranty claims must be submitted through the original company of purchase. All claims must be shipped back to the original 
company of purchase with an approved RMA number listed as a reference on the shipping label and clearly printed on two 
opposing sides of the package(s); product in question must be inspected by Cognito Motorsports before replacement parts are 
shipped out. 

   

Product Consumer Safety and Warning 

The installation of this kit will  modify the suspension of your vehicle and may  cause it to handle significantly different than a 
factory equipped vehicle. Installing larger tires with modified suspension and increased ground clearance will significantly alter 
the  handling  characteristics  of  the  vehicle,  and  may  result  in  increased  braking  distances  as  well  as  changes  in  vehicle 
maneuverability and handling compared to the factory equipped vehicle. As with any vehicle, extreme caution and care must be 
used  to  prevent  loss  of  control  or  roll-over  during  sharp  turns  or  abrupt  maneuvers.  Always  wear  seat  belts  and  drive  safely, 
recognizing the reduced speeds and specialized driving techniques is required. 

This  suspension  system  will  not  strengthen  nor  reinforce  the  stock  frame  of  the  vehicle,  nor  will  it  increase 

rollover protection.  It is necessary to periodically inspect all suspension and drive train components for tightness of  fit or any 
damage.  Installation  of  these  parts  will  modify  the  height  of  the  vehicle  and  will  raise  the  center  of  gravity.    Altered  height 
modifications  and  off-road  operation  may  increase  your  vehicle’s  susceptibility  to  roll  over  conditions  and  may  cause  serious 
injury  or  death.    Many  states  regulate  the  height  modification  to  each  vehicle.    Check  the  laws  in  your  state  for  exact 
specifications.   Height modifications may affect the reaction, ride, handling, and wear factor of your vehicle’s components.   

Failure to drive this vehicle safely  may result in injury  or death!

 Do  not drive  this  vehicle  unless you  are 

familiar with its unique handling characteristics and are confident of your ability to maintain control under all driving conditions. 
Some  modifications  and  combinations  of  modifications  are  not  recommended,  unsafe,  and  may  not  be permitted  in  your  state. 
Consult your vehicle owner’s manual, the instructions accompanying this product, and your state laws before undertaking these 
modifications. The owner of the modified vehicle and the qualified mechanic required to install this product are responsible for 
the legality and safety of the vehicle being modified. 

Discover other performance steering parts on our website.

Summary of Contents for PISK3008









Reviews: