background image

 

Cohu Electronics 

 

 

 

 

 

 

 

5930 Series Thermal Camera User's Manual 
 

 

 

Cohu Electronics 

P

AGE

 11 

OF

 17 

3912 Calle Fortunada 

San Diego, CA 92123-1827 

Phone: 858-277-6700 

Fax: 858-277-0221 

 
 

2.5.2 

Mating Rear Panel Connector 

The connector that mates with the main signal connector of the Camera is manufactured by 
Amphenol and the part number is a PT06A-14-18S-SR.  This connector must be manufactured to 
the assembly procedure provided by Amphenol. 

2.6 

Main Rear Panel Digital Signal Connector 

The main digital signal connector is located on the rear panel of the Camera as shown in Figure 
5. 

2.6.1 

Camera Digital Signal Connector 

The digital signal connector that is mounted to the rear panel of the Camera is manufactured by 
fischer and the part number is DBPE 1031 A019-139.  This connector is hermetically sealed 
which means it is gastight therefore exceeds the NEMA 4 and IP67 water resistance rating of the 
Camera.  This connector is equipped with 19 contacts.  See Table 7 for digital signal pin 
descriptions. 

Table 7 - Digital Signal Pin Descriptions 

Pin 
Number(s) 

Direction 

Signal Name 

Signal Description 

Input 

 

Positive (+) LVDS external clock input. 
NTSC:  49.09090 MHz. 
PAL:  59.00000 MHz. 

Input 

ExtClk- 

Negative (-) LVDS external clock input. 
NTSC:  49.09090 MHz. 
PAL:  59.00000 MHz. 

Input 

 

Positive (+) LVDS external sync input. 

Input 

ExtSync- 

Negative (-) LVDS external sync input. 

10 

Input 

ExtClkEn_n 

External clock enable.  This input determines whether 
the Camera boots with an external or internal clock.  
Low (tied to PGND):  external clock,  Open:  internal 
clock. 

11 

Input 

PGND 

Power Ground. 

12 

Output 

Sprc 

Positive (+) LVDS serialized 16 bit processed FPA 
video data bits 0-7. 

13 

Output 

SprcFpaVid0- 

Negative (-) LVDS serialized 16 bit processed FPA 
video data bits 0-7. 

14 

Output 

Sprc 

Positive (+) LVDS serialized 16 bit processed FPA 
video data bits 8-15. 

15 

Output 

SprcFpaVid1- 

Negative (-) LVDS serialized 16 bit processed FPA 
video data bits 8-15. 

16 

Output 

SprcFpa 

Positive (+) LVDS serialized digital processed FPA 
video sync. 

17 

Output 

SprcFpaVidSync- 

Negative (-) LVDS serialized digital processed FPA 
video sync. 

18 

Output 

SprcFp 

Positive (+) LVDS serialized digital processed FPA 
video clock. 

19 

Output 

SprcFpaVidClk- 

Negative (-) LVDS serialized digital processed FPA 
video clock. 

Summary of Contents for 5935-1000/T100

















Reviews: