Coleman 5040-761 Instructions For Use Manual Download

Page: 4 / 16

Assembly

■

Identify Center Rear Support Bracket. It has six holes, various sizes.

■

Place Center Rear Support

Bracket in place over the center
screw.

■

Assemble one nut loosely over

the screw to attach the Center
Rear Support Bracket.

■

Turn unit over and assemble

large screw loosely through Cover
Pieces into base of Center Rear
Support Bracket.

■

Attach Post Base to Cylinder

Cover Pieces loosely with seven
Large Screws.

7 Required

Large Screw

1 Required

Large Screw

1 Required

Large Screw

■

Assemble three small screws

loosely through Cover Pieces into
Center Rear Support Bracket.

■

Attach one large screw loosely

at base of Side Support Bracket.

■

Attach a Side Support Bracket

loosely with Hex Nut at top.

Step 3

Step 2

1 Req’d

Hex Nut

1 Req’d

Hex Nut

3 Req’d

Small Screw

Step 1

(continued)

Step 2

(continued)

Summary of Contents for 5040-761

















Search results

Summary of Contents for 5040-761

Reviews:

Related manuals for 5040-761

Brands by name

Popular brands

Coleman 5040-761, Instructions For Use Manual

Search results

Summary of Contents for 5040-761

Reviews:

Related manuals for 5040-761

Brands by name

Popular brands