background image

10 

Splits 

Make sure your lane timers know whether to take splits. The lane timers should press 

Start/Stop one time for each split. Up to 10 splits can be recorded per race. 

 

After the Race 

As each swimmer finishes the race, the Lane Timer(s) in that lane will press one of the side 

buttons (Start/Stop) and then Reset on the Watch(es) assigned to that lane. After all Lane 

Timers press Start/Stop at the end of the race and then Reset, the Dolphin software writes the 

result file to the C:\CTSDolphin folder on the computer and the next race can be started. 

 

If one or more of the lane timers fails to press Reset after the race, that watch’s state will not 

have a yellow light. Before the next race, use the Reset Timers button (or shortcut r) to force 

a reset and cause the Dolphin software to write the result file. 

 

Getting the Race Results into your meet management software: 

Hy-Tek’s Meet Manager: 

1.

 

From the Run Menu in MEET MANAGER, press 

Ctrl-F3

 

2.

 

A list of Dolphin result files for the current 

Data Set

 (see below for information 

about data sets) will be displayed with the most recent file at the top.  

3.

 

Select the result file and click OK. MM will extract the times and place them in a 

window so that you can see up to 3 wireless watch times per lane plus the computed 

average for each lane if there is more than one wireless watch per lane.  

o

 

If there are 3 watches for a given lane, the middle time will be average time.  

o

 

If there are 2 watches for a given lane, the average will be computed based on the 

rule choice selected in 

Run / Preferences / Backup Times

. If you are OK with 

the times in the window, click Accept and these times will be stored in the 

database along with the pad and button times already stored. To see the pad times, 

the backup button times, and the backup watch times, press 

Ctrl-K

 or click the 

Calc: Ctrl-K

 button. When the time adjustment window is displayed, you can 

compare the backup wireless watch times to the pad time and the backup button 

average to help you decide what to do if there is a discrepancy between the pad 

time and then backup button time. See Hy-Tek MM help files for a sample time 

adjustment window with Dolphin Backup times.  

 

If you are keeping track of races by 

Race Number

 (see discussion below), you can use the 

Race # to help you select the correct wireless watch file. If things go smoothly, this race 

number should be the same for the wireless watch file and the timing console data file. 

 

Splash and other meet management software: 

Follow the instructions in your specific meet management software. 

 

 

 

 

Summary of Contents for Dolphin

























Reviews: