background image

22

TWO YEAR SUPREME WARRANTY:

For two years from date of retail purchase within Canada, MTD PRODUCTS LIMITED will, 
at its option, repair or replace, for the original purchaser, free of charge, any part or parts 
found to be defective in material or workmanship. This warranty covers units which have 
been operated and maintained in accordance with the owner’s instructions furnished with the 
unit, and which have not been subject to misuse, abuse, commercial use, neglect, accident 
improper maintenance or alteration. Normal wear parts or components thereof are subject to 
special terms as noted below in the Ninety Day Consumer Warranty clause.
The engine, starter motor or component parts thereof carry separate warranties from their 
manufacturers. Please refer to the applicable manufacturer’s warranty policy for these items.

Ninety Day Consumer Warranty on Normal Wear Parts:

 All normal wear part failures 

will be covered on this product for a period of 90 days. After 90 days but within the two year 
warranty period, normal wear part failures will be covered if caused by defects in material or 
workmanship of other component parts.  Normal wear parts are defined as batteries, belts, 
blades, blade adaptors, grass bags, rider deck wheels, seats, tires and clutch parts (friction 
wheels).

Full Ninety Day Warranty on Battery (if equipped):

  For ninety (90) days from the date 

of retail purchase, if any battery included with this unit proves defective in material or work-
manship and our testing determines the battery will not hold a charge, MTD PRODUCTS 
LIMITED will replace the battery at no charge to the original purchaser.

Additional Limited Thirty Day Warranty on Battery (if equipped):

  After ninety (90) days 

but within one hundred twenty (120) days from the date of purchase, MTD PRODUCTS 
LIMITED will replace the defective battery, for the original purchaser, for a cost of one-half 
(½) of the current retail price of the battery in effect at the date of return.

Personal use: 

THE FOREGOING PARAGRAPHS CONSTITUTE THE MANUFACTURER’S 

ENTIRE WARRANTY WITH RESPECT TO ANY PRODUCT PURCHASED AND USED 
FOR PERSONAL FAMILY, HOUSEHOLD/RESIDENTIAL PURPOSES, AS DISTINGUISHED 
FROM COMMERCIAL USAGE.

Commercial use: 

ALL APPLICATIONS OTHER THAN PERSONAL USE AS OUTLINED 

ABOVE, ARE CONSIDERED COMMERCIAL USAGE.
New products purchased for commercial usage are warranted in the same manner and to the 
same extend EXCEPT the term of warranty will be 90 DAYS from date of purchase.

How to Obtain Service:

  Warranty service is available, with proof of purchase, through 

your local MTD Authorized Service Dealer.  If you do not know the dealer in your area, 
please write to the Service Department of MTD PRODUCTS LIMITED, P.O. BOX 1386, 
KITCHENER, ONTARIO N2G 4J1.  The return of a complete unit will not be accepted by the 
factory unless prior written permission has been extended by MTD PRODUCTS LIMITED.

Other Warranties:

  All other warranties, express or implied, including any implied warranty 

of merchantability is limited in its duration to that set forth in this express limited warranty.  
The provisions as set forth in this warranty provide the sole and exclusive remedy of MTD 
PRODUCTS LIMITED obligations arising from the sale of its products.  MTD PRODUCTS 
LIMITED  will not be liable for incidental or consequential loss or damage.

9

Warranty

Failure to comply 

with suggested 

maintenance 

and lubrication 

specifications will 

void warranty.

06.18.06

Summary of Contents for 31AE5LKH
























Reviews: