background image

8

4

Operating 

Your Lawn 

Mower

Blade Control Handle

The blade control handle is located on the upper handle 
of the mower. See Figure 4-1. The blade control handle 
must be depressed in order to operate the unit. Release 
the blade control handle to stop the engine and blade. 

Drive Control Handle

The drive control handle is located on the underside 
of the upper handle. Squeeze the drive control handle 
against the upper handle to engage drive system. 
Release the control handle to disengage the drive 
system in order to stop, slow down, or backup. 

Recoil Starter

The recoil starter is attached to the right upper handle. 
Stand behind the unit and pull the recoil starter rope to 
start the unit.

Cutting Height Adjustment Lever

The height adjuster determines the cutting height of the 
mower. The adjuster is located above the left rear wheel, 
refer to the Adjustment Section. 

Mulch Plug

The mulch plug is used for mulching purpose. Instead of 
collecting the grass clippings in the grass catcher, your 
mower has the option of recirculating the clippings back 
to the lawn. Make sure that the rear discharge door is 
closed and the grass catcher is removed from unit while 
mulching.

Know Your Lawn Mower

Speed Control

The speed control is located on the variable speed control 
housing on the upper handle. This control is used to select 
the forward speed of the mower. See Figure 4-1 inset.
IMPO

RTANT:

 Move the speed control only when the 

engine is running. Changing the speed control setting with 
the engine off can damage the mower.

NOTE

: The speeds noted on the speed control are not 

exact. Speed will vary depending on belt wear, cable wear, 
and mowing conditions.

Electric Start Ignition Switch

The electric start ignition switch is located on the right 
side of the  variable speed control housing on the upper 
handle. It is used only for the electric starter.

Before Starting 

1.  Service the engine with gasoline and oil as instructed 

in the separate engine manual. 

WARNING: Be sure no one other than the 
operator is standing near the lawn mower 
while starting engine or operating mower. 
Never run engine indoors or in enclosed, 
poorly ventilated areas. Engine exhaust 

contains carbon monoxide, an odorless 
and deadly gas. Keep hands, feet, hair 
and loose clothing away from any moving 
parts on engine and lawn mower. 

WARNING

Figure 4-1

Read, understand, 

and follow all instruc-

tions and warnings 

on the machine and 

in this manual before 

operating.

This blade control 

mechanism is a 

safety device. Never 

attempt to bypass its 

operations.

Use extreme care 

when handling 

gasoline. Gasoline is 

extremely flammable 

and the vapors are 

explosive. 

Never

 fuel 

the machine indoors 

or while the engine 

is hot or running. 

Extinguish cigarettes, 

cigars, pipes and 

other sources of 

ignition.

Recoil Starter

Electric Start 
Ignition Switch

Blade Control

Drive Control

Speed Control

Cutting Height 
Adjustment Lever

Mulch Plug

Summary of Contents for J830 Series
















Reviews: