background image

 

 

 

20

DAILY MAINTENANCE 

 

 

CLEANING THE RECOVERY TANK 

1.  Empty the tank through the hose, turning the knob a few turns and then pulling out 

the drain plug 

 

This operation must be carried out using gloves to protect against 
contact with dangerous solutions. 

 

 

2.  Disconnect the hinges of the suction cap (1) from the tank 
3.  Raise the cap until the prop (2) is hooked to the prop (3) of the recovery tank. 
4.  Check the filter inside the cover (4) is clean and, if necessary, loosen the cover 

fixing screws and carefully rinse the filter 
 

 

 

5.  Check the electric float (5) inside the tank is clean 
6.  Rinse the recuperation tank and clean the drain plug 
7.  Reposition the cap on the drainage tube and lower the suction cap. To release the 

props (2 and 3), just raise the cap slightly, push the connection joint (6) forwards 
and lower it again until the props rotate between them 

8.  Reconnect the hinges to the recovery tank 
 

 

 

CLEANING THE SQUEEGEE 

Clean the squeegee with a jet of water. Check the condition of the rubbers and 
reverse or replace them as necessary. Careful cleaning of the entire aspiration unit 
ensures a longer working life for the aspiration motor. 
Clean the squeegee tube and make sure it is not clogged. 

 

 

Summary of Contents for FLEXY 70BS






























Reviews: