COMESTERO GROUP
M21/03.02
Rev.02
of 25/09/03
Page 15 of 34
8
8
.
.
1
1
V
V
A
A
L
L
I
I
D
D
A
A
T
T
O
O
R
R
C
C
O
O
N
N
F
F
I
I
G
G
U
U
R
R
A
A
T
T
I
I
O
O
N
N
(
(
R
R
M
M
5
5
X
X
0
0
0
0
)
)
In standard validator configuration, RM5 can manage up to six different coin values, i.e. up to six
different outputs. Standard validator means a validator which further to the introduction of a coin
gives as validation signal a pulse to the corresponding output. The standard pulse length is 100
msec ( +0 -2% ); nevertheless it can be varied between 10mSec. and 2 sec. NOTE: When a value
ranging between 10 and 630 msec is set, the ratio 1 to 4 is guaranteed, i.e.the pulse will be active
(low) for the fixed timed, while the pause time between one pulse and the other will be four times
as much. When a value higher than 630 msec is set, the pause time will not follow this rule.
To inhibit one or more coins adjusted on the first 6 channels it is sufficient to put the DIP-SWITCH
relevant to the channel to be inhibited to “ON”. To inhibit the coins programmed in the channels
after 6 the PC kit or RM5 PROGRAMMER shall be used.
The coin validator has a general inhibiting pin, PIN 6, (see connector), which when set on HIGH
(+5Vdc, +12Vdc.) completely inhibits the coin validator, therefore each coin introduced would
always be rejected.This pin is usually controlled by the machine if this is out of order.
There is also the possibility to inhibit the validator after a fixed number of coins introduced by
setting, by means of the relevant programming kits (PC Kit or RM5 PROGRAMMER) the “cash
limit” function.
Whn the validator reaches the programmed threshold it will be disabled; to be enabled again the
machine shall send a reset signal to the validator inhibition pin.
This application is particularly used on “BINGO” machines and small-sized coffee machines and on
all machines with a limited number of accepted coins.
To separate coins from tokens a coin separator can be installed. To this purpose the validator shall
be programmed, by means of Clone5, to manage the separator (RM5 x 01). When the separator
function is enabled, the validator can manage the first 4 channels, as the outputs relevant to
channels 5 and 6 (Pin 3 and 4) are used to control the separation coils.
NOTE: the RM5 X 00 validator is totally interchangeable with NRI G13 validator and with COIN
CONTROLS C 120 validator, with AZKOYEN AZ66 validator, Jofemar T11 MS 130 MARS, G18
NRI and FAGE validator. Thanks to the mechanical adapter it can be turned from 3.5” to 5”
standard thus becoming also mechanically interchangeable with the abovementioned 24VDC
validators when these are installed on an RM1000 support or Juke Boxes with 5” validator. An
interface has also been produced to make electronically interchangeable the validator with MARS
111 validators PNP outputs (MRS 111 interface) as well as from a mechanical point of view thanks
to the front panel code RM F3 as shown in the paragraph “Front panel size”.
PIN-OUT OF RM5 X 00 COIN VALIDATOR 10 PIN CONNECTOR
Pin No.
Meaning
Pin No.
Meaning
1
Gnd
6
Inhibit
2
+12-24 Vdc
7
CH 1
3
CH 5
8
CH 2
4
CH 6
9
CH 3
5
N.U.
10
CH 4
8
8
.
.
2
2
C
C
C
C
T
T
A
A
L
L
K
K
V
V
A
A
L
L
I
I
D
D
A
A
T
T
O
O
R
R
C
C
O
O
N
N
F
F
I
I
G
G
U
U
R
R
A
A
T
T
I
I
O
O
N
N
(
(
R
R
M
M
5
5
X
X
C
C
C
C
)
)
In validator configuration with CC TALK protocol, RM5 can manage up to sixteen different coin
values. The equipment will respond to serial controls described below.
