22
• bag of accessories with:
- the operating and maintenance manual;
- the engine operating and maintenance manual;
- the declaration of conformity;
- the booklet giving the assistance centres;
- the warranty certificate;
- the handle fixing kit: screws, washers (ENDURANCE);
- suction kit with: fitting, gasket and clamp;
- nozzle cleaning needle;
If any problems arise please contact your dealer or an authorised assistance centre.
OPTIONAL ACCESSORIES
You can add the following range of accessories to the standard ones supplied with your high pressure
cleaner:
• sandblasting lance: designed to smooth surfaces, removing rust, paint, encrustations, etc.;
• drain cleaning kit: designed to unclog pipes and ducts;
• different types of lances and nozzles;
• rotating brush: designed for cleaning fragile surfaces;
• rotating nozzle: designed for removing stubborn dirt;
• foam lance: designed for a more efficient distribution of the detergent;
INSTALLATION - ASSEMBLING THE ACCESSORIES
AND FILLING THE ENGINE CRANKCASE WITH OIL
• Fix the handle (4) to the frame (3) using the kit supplied: screws (5), washers (6) and nuts (7) for FDX
ENDURANCE (in this case use a 13 mm fixed jaw spanner, not supplied).
Operation A
in Fig. 1, 2, 3 and
4.
• Unwind the high pressure hose (30) and screw the end without the quickfit coupling onto the spray
gun (19) thread and tighten well with two 22 mm fixed jaw spanners (not supplied).
Operation B
in Fig. 7.
• Connect the quickfit coupling (34) to the water outlet fitting (15), screw down and tighten the ring nut
by hand.
Operation C
in Fig. 7.
• Insert the gasket (49) (FDX ENDURANCE) or the water inlet filter (39) (for all the other models) in the
water inlet fitting (16) and screw the water inlet hose-end fitting (11) on to it.
Operation D
in Fig. 7.
• Clamp (37) the free end of the detergent suction hose (31) to the detergent suction fitting (36).
Operation E
in Fig. 7.
• Fill the engine crankcase with oil, following the instructions given in the relevant operating and
maintenance manual (this is not to be done on machines with Diesel engines as they are filled with
oil in the factory).
OPERATION – PRELIMINARY ACTIVITIES
• Do the preliminary activities described in the operating and maintenance manual of the engine
mounted on the high pressure cleaner. In particular remember to fill with fuel and check the level of
engine oil.
• When the engine is off and the machine is completely cold, check the level of pump oil by way of the
level indicator (38). Also check the gearbox oil level by way of the level indicator (44) on those models
thus equipped.
When topping up is needed please refer to the lubricant types given in the
“s
peCiFiCations
and
teChniCal
data
”
paragraph.
• Check correct tyre inflation.
• Check that the inlet water filter (39) and the detergent suction filter (40) are clean. The FDX ENDURANCE
models have a professional suction filter (23) that needs to be inspected less frequently (please refer
to the
“r
outine
M
aintenanCe
”
paragraph).
Summary of Contents for 9066 0101
