background image

 
 

 

 

 

IE-COM-D0221-05

 

 

 

 

 

Total memory capacity: 

1000 stored temperature sets 

manual logging mode 

8124 values for each channel 

automatic noncyclic logging mode 

7644 values for each channel 

automatic cyclic logging mode 

______________________________________________________________________________________________________________________________________________________________ 

The above specified numbers are maximum possible. Capacity is slightly lower if logging was interrupted by 

communication with computer, by stopping logging or switching OFF the instrument. 

 

Real time clock: 

Adjustable from computer, integrated calendar including leap years  
Real time clock accuracy: < 200 ppm (i.e. 0.02 %, 17.28 s in 24 h) 

 

Power: 

Battery 9V or ac/dc adapter 12 V with NiMH accumulator 9V 

_____________________________________________________________________________________________________________________________________________________________ 

If instrument is supplied from external ac/dc adapter, internal 9V battery should be replaced with rechargeable 
NiMH  accumulator.  In  usual  operation  from  adapter  accumulator  is  charged  only  with  small  current.  If 

accumulator is totally discharged, its full charging in instrument takes approximately 100 hours. Instrument with 

accumulator is not recommended for permanent operation without ac/dc adapter plugged. Accumulator works 

only as a standby source in case of power mains failure. 

 

Average current consumption: 

0.08 to 0.3 mA (depending on operation mode) 

_____________________________________________________________________________________________________________________________________________________________

 

Battery  life  depends  on  selected  display  refresh  mode  (see  below).  In  FAST  mode  display  is  refreshed  in 

shortest possible interval with highest current consumption. In dynamic mode display is refreshed in interval up 

to 5 s in case measured values remain stable. Refresh interval is shortened to approximately 0.7 s only if 

measured values change. Current consumption in this mode in usual operation is lower, battery life is up to 4 

times  longer.  The  FAST  mode  is  recommend  to  use  only  in  cases,  when  slower  display  response  is  not 
acceptable. 

Battery voltage drop below 7 V is indicated with blinking of "BAT" in default display mode (displaying of actual 

values) and FAST mode is automatically cancelled to save the battery. At the same time audio indication of 

alarms is automatically switched OFF.

 

 

Electromagnetic compatibility: 

Device conforms in accordance with EN 61326-1 these norms: 

 

Radiation: 

EN 55022 

class B  

Immunity: 

EN 61000-4-2 

(levels 4/8 kV, class A) 

 

 

 

EN 61000-4-3 

(intensity of electromagnetic field 3 V/m, class B) 

 

 

 

EN 61000-4-4 

(levels 1/0.5 kV, class A) 

 

 

 

EN 61000-4-6 

(intensity of electromagnetic field 3 V/m, class B) 

 

 

 

EN 61000-4-11  (class A) 

 

 

 

EN 61000-4-5 

(class A) 

 

 
 
 
 
 
 
 

Summary of Contents for Commeter D0221





















Reviews: