background image

 

 

15 

13 

 Battery voltage regulation 

 

Parameter  2:  Choose  “Add”  or  “Sub”  to  make  battery  voltage  Up  / 

Down adjustment. 
Parameter 3: Voltage regulation range 0 - 5.7V (default 0V). 

14 

 

Charger voltage adjustment

 

 

Parameter 2: Choose “Add” or “Sub” to make the Charger Voltage Up 

/ Down adjustment. 
Parameter 3: Voltage regulation range 0 - 9.9V (default 0V). 
The batteries must be disconnected before calibrating. 

15 

 Inverter voltage regulation 

 

Parameter 2: Choose “Add” or “Sub” to make the Charger Voltage Up 

/ Down adjustment. 
Parameter 3: voltage adjustment range 0 - 6.4V (default 0V). 

16 

 Adjusting the output voltage 

 

If the output voltage cannot be identified (below 50V) in the menu it is 
not possible to make changes. 

 

Parameter 2: Indicates the OP.V output voltage 
Parameter  3:  Indicates  the  UPS  output  voltage  measured  inside  the 
UPS. Using the arrow keys, calibrate the value of the output voltage to 
the actual value indicated by the meter. The result of the calibration is 
obtained  by  confirming  the  change  with  the  Enter  key.  Voltage 
regulation range +/- 9V. 

17 

 Setting and adjustment of the charging current 

 

Parameter 2: Charging current 001-004 means 1.2, 3, 4 A respectively 
 
Parameter 3: Correction of the charging current "+" or "-" by 0.1x the 
set value. 
For example, "+" "3" means the current is increased by +0.3A 

 

 

4.7. 

 

Description of the UPS operation modes 

Operation mode 

Description 

LCD status 

Normal 

mode 

(OnLine) 

In all online UPSs, fans are working all the time. The only difference is with speed 
rotation 

 

it depends on the temperaturę and the load, but are working non stop.

 

 

 

 

 

Summary of Contents for COVER CORE 10K
























Reviews: