background image

507712-01

Page 13  of  36

Issue 1642

Figure 16. Vent Connection

Use self drilling sheet metal screws or a mechanical 

fastener to firmly secure the vent pipe to the round collar of 

the flue transition. If self drilling screws are used to attach 

the vent pipe, it is recommended that three be used. Drive 

one self drilling screw through the front and one through 

each side of the vent pipe and collar. See Figure 16.

Install the first vent connector elbow at a minimum of six 

inches (152 mm) from the furnace vent outlet. See Figure 

16.

Venting Using a Masonry Chimney

The following additional requirements apply when a lined 

masonry chimney is used to vent this furnace.

Masonry chimneys used to vent Category I central furnaces 

must be either tile lined or lined with a listed metal lining 

system or dedicated gas vent. Unlined masonry chimneys 

are prohibited. See Figures 17 and 18 for common venting.

A chimney with one or more sides exposed to the outside 

of the structure is considered to be an exterior chimney.

An exterior masonry chimney that is not tile lined must be 

lined with B 1 vent or a listed insulated flexible metal vent. 

An exterior tile lined chimney that is sealed and capped 

may be lined with a listed uninsulated flexible metal vent.

If the existing chimney will not accommodate a listed metal 

liner, either the chimney must be rebuilt to accommodate 

one of these liners or an alternate approved venting 

method must be found.

Insulation for the flexible vent pipe must be an encapsulated 

fiberglass sleeve recommended by the flexible vent pipe 

manufacturer.

Figure 17. Common Venting Using Metal Lined

Masonry Chimney

NOTE 1:

 

Refer to the provided venting tables for installations. 

Refer to the capacity requirements shown in the provided venting 

tables.

DO NOT

 insulate the space between the liner and the 

chimney wall with puffed mica or any other loose granular 

insulating material.

Figure 18. Common Venting Using Tile Lined Interior Masonry Chimney and Combined Vent Connector

NOTE

: Refer to provided venting 

tables for installations.

NOTE: 

The chimney must be properly 

sized per provided venting tables or 

lined with listed metal lining system.

Summary of Contents for GDD80A





































Reviews: