background image

DUAL BURNER BILTMORE SPLIT OAK

18" AND 24"

THERMOSTATICALLY-CONTROLLED MODELS

LOG AND BURNER SETS:

BILTMORE18LTN/P AND BILTMORE24LTN/P

PIL

OT

 

O

F

F

 

O

N

 

LO

REMOTE

OFF

HI

 

 

Biltmore18LTN
Biltmore18LTP

Biltmore24LTN
Biltmore24LTP

 -  Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other 

appliance.

 -  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance. 

•  Do not touch any electrical switch; do not use any phone in your building. 

•  Leave the building immediately.

• Immediately call your gas supplier from a neighbor’s phone.  Follow the gas supplier’s instructions. 

•  If you cannot reach your gas supplier, call the fire department.

 -  Installation and service must be performed by a qualified installer, service agency or the gas supplier.

       WARNING:
FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.
This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where not 

prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This 

appliance is not convertible for use with other gases.

Installation and Operation Instructions

Models

PFS

®

US

C

Report No. F09-126

P/N 900555-00   Rev. NC   12/2015

Biltmore

TM

 Unvented (Vent-Free) Gas Log Heaters

WELCOME HOME TO WARMTH

TM

P900555-00

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions 

for adequate combustion and ventilation air must be provided. Refer to Air for Combustion and Ventilation 

section on page 5 of this manual.

Summary of Contents for Biltmore18LTN





























Reviews: