background image

6

6

www.comfortzoneproducts.com

LIMITED WARRANTY 

This unit is guaranteed to the original retail purchaser 
against defects in quality or workmanship for a period of 
one year from the date of original purchase. If this unit 
fails because of a manufacturing defect within 30 days of 
purchase, return the unit, with your receipt, to the retailer. 
After 30 days, but within the warranty period, if the unit 
was purchased within the continental United States, 
return it, freight prepaid, to World and Main for repair 
or replacement. If the unit was purchased outside the 
continental United States, return the unit to the place of 
purchase. This warranty does not cover damage caused 
by misuse, abuse, overheating or alteration. Repairs made 
by anyone other than World and Main are not covered in 
this warranty. World and Main will not be held liable for any 
losses due to neglectful operation. All implied warranties, 
including the warranties of merchantability and of fitness 
of purpose, if applicable, are hereby limited in duration 
to the period of one year from the date of original retail 
purchase. Some states do not allow limitations on how 
long an implied warranty lasts, so the above limitations 
may not apply to you. Incidental or consequential 
damages arising from a breach of either express or implied 
warranties are hereby disclaimed and excluded. Some 
states do not allow the exclusion of limitation of incidental 
or consequential damages, so this limitation or exclusion 
may not apply to you. Upon the expiration of this warranty 
all such liability will terminate. No other warranties are 
expressed or implied.

This warranty gives you specific legal rights, and you may 
also have other rights which vary from state to state. No 
informal dispute settlement mechanisms are available. 
This limited warranty is given in lieu of all other warranties.

Manufactured for:  
World and Main (Cranbury), LLC  
324A Half Acre Rd.  
Cranbury, NJ  08512 USA  
800-221-6895  
www.comfortzoneproducts.com

Rev. 10/05/21

Fig 1

 

Slide Cover to Open   

Fig 2

Fig 3

 

CARE AND MAINTENANCE: 

Cleaning:

 

CAUTION-Before cleaning the fan be sure to 

disconnect power cord from the plug. Clean the grille surface 
with a clean damp cloth. Do not use harsh chemical or abrasive 
cleaners. DO NOT IMMERSE THE FAN OR ANY WIRES IN 
WATER. Allow fan to dry completely before use. Periodic grille 
cleaning with a vacuum will prevent dust build up. The motor is 
sealed and does not require any interior maintenance, cleaning 
or lubrication.

Maintenance:

 

The Internal motor bearings are permanently 

lubricated at the factory and do not require any additional 
lubrication.

Repair:

 

DO NOT OPERATE THE FAN WITHOUT THE GRILLE IN 

PLACE. DO NOT USE THE FAN IF IT HAS MALFUNCTIONED OR 
BECOME DAMAGED IN ANY WAY.

Storage:

 

Keep original carton for storage of the fan. Coil and tie 

the power cord to avoid damage during storage.

Note

:

 Some models come with a plug where you can replace 

a fuse. If your model has this, please read and follow the below 
instructions to replace the fuse.

This product employs overload protection (fuse). A blown fuse 
indicates an overload or short-circuit situation. If the fuse blows, 
unplug the product from the outlet. Replace the fuse as per the 
user servicing instructions (follow product marking for proper 
fuse rating) and check the product. If the replacement fuse 
blows, a short-circuit may be present and the product should 
be discarded or returned to an authorized service facility for 
examination and/or repair.

Fuse Replacement:

1. Grasp plug and remove from the receptacle or other 

outlet device. Do not unplug by pulling on cord. 

2. Open fuse cover by sliding open fuse access cover on 

top of attachment plug towards blades. See Fig. 2 

3. Remove fuse carefully. Use a small tool to pry the end 

of the fuse from holder cavity. Be careful not to break 
glass window. 

4. Replace fuse.  

WARNING:

 Risk of fire. Replace fuse only with identical 

2.5 or 5.0 Amp, 125 Volt fuse (3.6mm x 10mm). Be sure 
fuse is properly seated within its cavity. 

5. Close fuse cover by sliding it back to its original closed 

position. 

Reviews: