4
4
CZ700T
www.comfortzone-us.com
Limited Warranty
Products manufactured by Comfort Zone
®
are warranted to
the original consumer to be free of defects in material and
workmanship for twelve (12) months from the original date
of purchase. The warranty does not cover products modified
outside our factory, damage or failure caused by acts of God,
abuse, misuse, abnormal usage, faulty installation, failure to
follow suggested maintenance procedures enclosed with this
product (as defined by Magnuson-Moss Warranty-Federal
Trade Commission Improvement Act). This unit is guaranteed
to the original retail purchaser against defects in quality or
workmanship for a period of one year from the date of original
purchase. If this unit fails because of a manufacturing defect
within 30 days of purchase, return the unit, with your receipt, to
the retailer. After 30 days, but within the warranty period, if the
unit was purchased within the continental United States, return it,
freight prepaid, to Comfort Zone
®
for repair or replacement. If the
unit was purchased outside the continental United States, return
the unit to the place of purchase. This warranty does not cover
damage due to accidents, operation on other than 120 volts /
60 hertz A.C. current, or any other abuse. All implied warranties,
including the warranties of merchantability and of fitness of
purpose, if applicable, are hereby limited in duration to the period
of one year from the date of original retail purchase. Some States
do not allow limitations on how long an implied warranty lasts,
so the above limitations may not apply to you. Incidental or
consequential damages arising from a breach of either express
or implied warranties are hereby disclaimed and excluded. Some
states do not allow the exclusion of limitation of incidental or
consequential damages, so this limitation or exclusion may not
apply to you.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
No informal dispute settlement mechanisms are available. This
limited warranty is given in lieu of all other warranties.
Manufactured for:
Howard Berger Co. LLC
324A Half Acre Rd.
Cranbury, NJ 08512 USA
800-221-6895
www.comfortzone-us.com
Rev. 080215
Care and Maintenance
Cleaning:
CAUTION-Before cleaning the fan be sure to
disconnect power cord from the plug. Clean the grille surface
with a clean damp cloth. Do not use harsh chemical or abrasive
cleaners. DO NOT IMMERSE THE FAN OR ANY WIRES IN
WATER. Replace front grille before fan use. Allow fan to dry
completely before use. Periodic grille cleaning with a vacuum will
prevent dust build up. The motor is sealed and does not require
any interior maintenance, cleaning or lubrication.
Maintenance:
The Internal motor bearings are permanently
lubricated at the factory and do not require any additional
lubrication.
Repair:
DO NOT OPERATE THE FAN WITHOUT THE GRILLE IN
PLACE. DO NOT USE THE FAN IF IT HAS MALFUNCTIONED OR
BECOME DAMAGED IN ANY WAY.
Storage:
Keep original carton for storage of the fan. Coil and tie
the power cord to avoid damage during storage.
This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse blows,
unplug the product from the outlet. Replace the fuse as per the
user servicing instructions (follow product marking for proper
fuse rating) and check the product. If the replacement fuse
blows, a short-circuit may be present and the product should
be discarded or returned to an authorized service facility for
examination and/or repair.
Fuse Replacement:
1. Grasp plug and remove from the receptacle or other outlet
device. Do not unplug by pulling on cord.
2. Open fuse cover by sliding open fuse access cover on top of
attachment plug towards blades. See Fig. 2.
3. Remove fuse carefully. Use a small tool to pry the end of the
fuse from holder cavity. Be careful not to break glass window.
4. Replace fuse. WARNING: Risk of fire. Replace fuse only with
identical 2.5 or 5.0 Amp, 125 Volt fuse (3.6mm x 10mm). Be
sure fuse is properly seated within its cavity.
5. Close fuse cover by sliding it back to its original closed
position.
Fig 1
Fig 2
Fig 3
Slide Cover to Open
