background image

4

4

www.comfortzoneproducts.com

Rev. 11/08/21

LIMITED WARRANTY 

This unit is guaranteed to the original retail purchaser against defects in quality or workmanship for a period of one year from the date 

of original purchase. If this unit fails because of a manufacturing defect within 30 days of purchase, return the unit, with your receipt, 

to the retailer. After 30 days, but within the warranty period, if the unit was purchased within the continental United States, return it, 

freight prepaid, to World and Main for repair or replacement. If the unit was purchased outside the continental United States, return 

the unit to the place of purchase. This warranty does not cover damage caused by misuse, abuse, overheating or alteration. Repairs 

made by anyone other than World and Main are not covered in this warranty. World and Main will not be held liable for any losses due 

to neglectful operation. All implied warranties, including the warranties of merchantability and of fitness of purpose, if applicable, are 

hereby limited in duration to the period of one year from the date of original retail purchase. Some states do not allow limitations on 

how long an implied warranty lasts, so the above limitations may not apply to you. Incidental or consequential damages arising from a 

breach of either express or implied warranties are hereby disclaimed and excluded. Some states do not allow the exclusion of limitation 

of incidental or consequential damages, so this limitation or exclusion may not apply to you. Upon the expiration of this warranty all 

such liability will terminate. No other warranties are expressed or implied.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. No informal dispute 

settlement mechanisms are available. This limited warranty is given in lieu of all other warranties.

Manufactured for:

World and Main (Cranbury), LLC

324A Half Acre Rd.

Cranbury, NJ  08512 USA

800-221-6895

www.comfortzoneproducts.com

Note: 

Some models come with a plug where you can replace a fuse. If your model has this, please read and follow the below 

instructions to replace the fuse. 

This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug 

the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and 

check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an 

authorized service facility for examination and/or repair.

Fuse Replacement:

1.  Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2.  Open fuse cover by sliding open fuse access cover on top of  

attachment plug towards blades. See Fig. 2.

3.  Remove fuse carefully. Use a small tool to pry the end of the  

fuse from holder cavity. Be careful not to break glass window.

4.  Replace fuse. WARNING: Risk of fire. Replace fuse only with  

identical 2.5 or 5.0 Amp, 125 Volt fuse (3.6mm x 10mm).  

Besure fuse is properly seated within its cavity.

5. Close fuse cover by sliding it back to its original closed position.

Troubleshooting Chart

Work Should be Done by a Factory Authorized Service Center

Symptom

Possible Causes

Corrective Action

Fan fails to operate

1.  Cord not plugged in

2.  Fuse blown or circuit breaker open

3.  Low voltage

4.  Defective switch

5.  Motor winding open

6.  Motor bearings dry

7.  Limit control

1.  Plug cord into outlet

2.  Replace fuse or reset breaker

3.  Ensure that there is proper voltage at outlet

4.  Replace switch

5.  Replace motor

6.  Replace motor

7.  Vacuum air blockage on fan guards; Clear air 

obstruction; wait for motor to cool down

Fan operates noisily

1.  Motor bearings dry

2.  Fan blade loose

1.  Replace motor

2.  Tighten fan blade

Fan vibrates

1.  Fan sitting on uneven or inclined 

surface

2.  Fan blade dirty

3.  Fan blade broken or bent

1.  Place fan on level surface

2.  Clean fan blade (see Maintenance)

3.  Replace fan blade

Fig 1

Fig 2

Fig 3

Slide Cover to Open

Reviews: