background image

V30/30 DISTRIBUTION PANEL 

SETUP AND OPERATION MANUAL  

  

 OPERATION - PAGE 13

5.4  bus Calibration

To access bus calibration settings from the home screen, press the 

Settings icon, then press Bus Calibration.

5.4.1  bus Load

Bus Load can be adjusted up to +/- 15 increments 

(+/- 15A)

. Voltage 

adjustment offset is shows on the right side of the display.

5.4.2  bus Voltage

Voltage can be adjusted up to +/- 30 increments 

(+/- 3.0V)

. Voltage 

adjustment offset is shown on the right side of the display. 

5.5  System

To access system settings from the home screen, press the Settings icon, 

then press System. 

5.5.1  Display

5.5.1.1  brightness/buzzer Volume

The display brightness and buzzer volume can be adjusted by moving 

the sliders. 

5.5.2  Touch Calibration

This setting prompts user for permission to proceed with touch 

calibration. Follow instructions on screen to continue.

5.5.3  Settings

5.5.3.1  Input Feeder Size

Press the SET button to adjust feeder fuse size for A1, A2, B2, and B1 

busses.

1.  Use keypad to enter a feeder fuse size between 100A and 300A. 

2.  Press SAVE button to save feeder fuse size, or CANCEL to revert back 

to old feeder fuse size.

5.5.3.2  Input Feeder Threshold

Press the SET button to adjust feeder fuse threshold for A1, A2, B2, and 

B1 busses.

1.  Use keypad to enter a feeder fuse threshold between 40% and 100%. 

2.  Press SAVE button to save feeder fuse threshold, or CANCEL to revert 

back to old feeder fuse threshold.

5.5.3.3  bus Redundancy

Turn bus redundancy ON/OFF by pressing the check box next to Bus 

Redundancy. 

5.5.4  Information

This screen displays system information about controller and 

temperature sensors.

Cont = Controller internal temperature sensor. 1-4 are reserved for 

optional external temperature sensors. 

Figure 17.  bus Load Calibration

Figure 18.  bus Voltage 

Calibration

Figure 19.  Display

Figure 20.  Touch Calibration

Figure 21.  Settings

Figure 22.  Input Feeder Size

Figure 23.  Input Feeder Threshold

Figure 24.  System Information

Summary of Contents for v30/30































Reviews: