background image

       

  

 

                                                                                                                                                                                                             

 

www.commscope.com 
© 2016 CommScope, Inc. All rights reserved. 
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information. 
All trademarks identified 

by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. D701-0006  D (10/16)                            Page 1 of 7 

 

 
D701-0006       Revision D,       October 2016   

 

Multi-Beam Panel Antenna 5UPX0805F 

 

 

General

 

 
This instruction sheet contains all necessary information required to assist in the correct installation 
of CommScope Multi-Beam Panel Antennas.  
 

 
The following symbols can be found next to text outlining important information. 
 

 

Please follow the procedure marked with this symbol precisely. 
Non-compliance may lead to damage of the product. 

 

 

 

Handy tips when installing product. 

 
 

Unpacking 

 
Make sure that the antenna and the accessory items listed below are provided and have not been 
damaged during transport. 
 

 

Antenna 

 

Mounting kit 

 

Installation Instructions (This document) 

 

Mounting Kits 

Type 

QTY 

Fixed Downtilt 

F-042-GL-E 

Mechanical Downtilt 

T-041-GL-E 

 

 
 

 

DO NOT STACK 

UNPACKED ANTENNAS 

 

 

 

DO NOT PLACE  POINT 

LOADS ON ANTENNA 

RADOME 

 
 
 

Summary of Contents for 5UPX0805F








Reviews: