CommScope FOSC-500-AA Installation Instruction Download | Manualshive

Page: 8 / 12

background image

8

5.19 Place the fibers underneath the lips.

5.20 Turn the splices 180° and install the splices in the SMOUV
holder (hinged side).

5.17 Install the splices in the SMOUV holder (non hinged side).

5.18 Route the fiber from the SMOUV holder to the storage area
over the edge of the cassette leaving no slack through the opening (1).

1

Top, non-hinged side

Top, hinged side

«
...
6
7
8
9
10
...
»

Summary of Contents for FOSC-500-AA













Reviews:

No comments

Related manuals for FOSC-500-AA

Brand: Vantec Pages: 23

Brand: Eaton Pages: 70

Brand: UFO Pages: 20

Brand: 4ms Company Pages: 4

CONCOURSE CSUB -

Brand: QUAD Pages: 4

Brand: Renkforce Pages: 4

Brand: Renkforce Pages: 8

Brand: Leviton Pages: 2

Brand: Crestron Pages: 16

Brand: APLIC Pages: 20

Brand: Razer Pages: 10

Brand: X-media Pages: 7

Brand: NVX Pages: 7

FieldSmart Fiber Active Cabinet 400

Brand: Clearfield Pages: 139

Brand: StarTech.com Pages: 19

Brand: GAMDIAS Pages: 13

Brand: HPE Pages: 71

Brand: Bartec Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands