CommScope iP-600A-12-CSC-SMF Instruction Sheet Download

Page: 1 / 12

SYSTIMAX

Solutions

www.commscope.com

Instruction Sheet 860106368

Issue 6, December 2012

SYSTIMAX

iPatch

600A Shelf with Faceplate Instructions

For RoHS Inquiries:

CommScope Inc.

Corke Abbey, Bray

Co. Dublin, Ireland

Attn: Legal Department

Page 1 of 12

General

The

iPatch

600A shelf with faceplate is a

SYSTIMAX

approved product. This distribution shelf provides for

connection of non-metallic Outside Plant (OSP) cable or Lightguide Building Cable (LGBC) to 12

iPatch

duplex fiber ports or 24

iPatch

LC duplex fiber ports either by direct termination or splicing. Designed for use in

iPatch

system, this shelf is one unit high and can be mounted in a standard 19-inch rack with a universal hole

pattern.

Note:

To use the

iPatch

600A shelf in an existing

iPatch

system, the network manager and rack managers

must be running software version 6.03 or later. The System Manager software, used to manage the system,

must be Version 6.2 or later. We recommend that you upgrade the System Manager software to Version 6.2 or a

later version before you install the shelf. System Manager will automatically upgrade the

iPatch

Manager

software.

Ordering information is listed below:

Material ID

Part No.

Description

760005595

iP-600A-12-SC-MMF

600A fixed multimode intelligent fiber shelf, SC 12 port duplex

760080887

iP-600A-12-CSC-SMF

600A fixed SC single-mode intelligent fiber shelf, 12 port duplex ceramic

How to Contact Us

•

To find out more about

CommScope

products, visit us on the web at

http://www.commscope.com/

•

For technical assistance:

Within the United States, contact your local account representative or technical support at

1-800-344-0223. Outside the United States, contact your local account representative or Authorized

Business Partner.

Within the United States, report any missing/damaged parts or any other issues to

CommScope Customer Claims at 1-866-539-2795. Outside the United States, contact your

local account representative or Authorized Business Partner.

This product is covered by one or more of the following U.S. patents or their foreign equivalents: 6,285,293 and 6,522,737.

Summary of Contents for iP-600A-12-CSC-SMF













Search results

Summary of Contents for iP-600A-12-CSC-SMF

Reviews:

Related manuals for iP-600A-12-CSC-SMF

Brands by name

Popular brands

CommScope iP-600A-12-CSC-SMF, Instruction Sheet

Search results

Summary of Contents for iP-600A-12-CSC-SMF

Reviews:

Related manuals for iP-600A-12-CSC-SMF

Brands by name

Popular brands