CommScope iP-600A-12-CSC-SMF Instruction Sheet Download

Page: 2 / 12

860106368

Instruction Sheet

www.commscope.com

Page 2 of 12

Parts List

Verify parts against the parts list below:

Quantity

Description

Shelf with the one of the following items installed: fixed fiber tray;

iPatch

SC duplex fiber faceplate (12 ports) or

iPatch

LC duplex fiber faceplate (24 ports);

183U1 cover

Panel bus jumper

Mounting brackets

3-inch storage drums

Splice organizer holders

Adhesive-backed wire retainers

#12-24 x 3/8 inch screws for mounting the shelf

Liquid tight cable fittings with lock nuts

Plastic cable tie retainers

Cable ties

Fiber type labels (8 labels each sheet)

Double-sided tape (6 inches / 15.2cm) for mounting splice organizers

Instruction sheet

Separately Orderable Components

Material ID

Part No.

Description

700006257

1AF1-16LG

Fusion splice organizers

700006281

1AMF1-6LG

Mass fusion splice organizers

700006240

1AM1-12LG

Mechanical splice organizers

—

1U-19 Patch Cord Trough

Specifications

Fiber Optic Interface

Industry-standard SC or LC

Compatible Fiber Size

Multimode with 50 µm core diameter, such as

LazrSPEED

Multimode with 62.5 µm core diameter, such as

OptiSPEED

Singlemode with 8.3 µm core diameter, such as

TeraSPEED

Environmental Data

Temperature:

-40º F to 158º F (-40º C to 70º C) (storage)

Range:

14º F to 158º F (-10º C to 70º C) (operational)

Humidity: :

95% noncondensing

Summary of Contents for iP-600A-12-CSC-SMF













Search results

Summary of Contents for iP-600A-12-CSC-SMF

Reviews:

Related manuals for iP-600A-12-CSC-SMF

Brands by name

Popular brands

CommScope iP-600A-12-CSC-SMF, Instruction Sheet

Search results

Summary of Contents for iP-600A-12-CSC-SMF

Reviews:

Related manuals for iP-600A-12-CSC-SMF

Brands by name

Popular brands