CommScope OFDC-A4 SPLICE/PATCH Installation Instructions Manual Download | Manualshive

Page: 8 / 10

background image

Page 8 of 10

© 2019 CommScope, Inc. All Rights Reserved

7.4

Close the housing.

8

Patch application

8�1

Cable preparation, routing and

splicing at tray 2

In the patch application splicing is only possible at tray 2.

8.1.1

As supplied. Panel with adapters, pre-conn 900µ

pigtails and overlength stored.

8.1.2

Take out the 900µ pigtails.

7

Organizer installation in housing

7.1

Install the organizer in the housing by sliding the

organizer under the 2 screws.

7.2

Tighten the 3 screws.

7.3

Install blind plugs in all unused ports. Verify that

all fibers are properly routed via wire saddles (to avoid fiber

clamping).

«
...
6
7
8
9
10
»

Summary of Contents for OFDC-A4 SPLICE/PATCH











Reviews:

No comments

Related manuals for OFDC-A4 SPLICE/PATCH

POVCAM AG-HCK10G

Brand: Panasonic Pages: 3

Brand: Foxun Pages: 4

Brand: MDR Electronics Pages: 7

Brand: Hitachi Pages: 33

Ethereal CS-1X2HDMSPL

Brand: Metra Electronics Pages: 8

Brand: Daiwa Pages: 38

Brand: Nanocable Pages: 6

CM-3201 LTE Filter

Brand: Channel Master Pages: 2

Brand: Warmup Pages: 3

Brand: CommScope Pages: 7

Brand: Lindy Pages: 8

voltomat 2214 7008

Brand: BAHAG Pages: 43

Brand: Diablotek Pages: 1

Brand: Stahl Pages: 33

DialDim DNL.WHS.20500

Brand: Denali Pages: 5

Brand: Stahl Pages: 37

Brand: ENFORCER Pages: 2

Brand: ENFORCER Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands