background image

ADCP-96-806 • Issue 4 • July 2016

Page 5

© 2016 

CommScope

. All Rights Reserved.

Figure 2. Cabinet Dimensions

4. Using the template as a guide, drill pilot holes for the six 3/4-inch #10 panhead screws 

required for mounting the cabinet. 

5. Partially install the 

top

 

two

 #10 wood screws leaving the heads protruding about 1/4-inch

 

from the surface of the backer board. 

Do not tighten. 

6. Hang the cabinet on the two installed screws using the key-hole shaped slots. 

7. Level the cabinet, tighten the two top screws, and then install the remaining #10 screws. 

3

GROUNDING THE CABINET

This section provides instructions for connecting a grounding wire to the cabinet. Use the 
following procedure to ground the cabinet: 

1. Locate the grounding components that are provided separately with the cabinet. A

 

grounding lug kit (consisting of two external tooth washers, two nuts, one screw and one 
lug) is provided. 

2. Open the hinged middle-section of the cabinet to provide access to the cabinet’s 

termination and splicing compartment. 

3. Threaded inserts are provided on the left and right sides of the cabinet. Select one of the 

inserts for installation of the grounding components. 

4. Install the required grounding components as shown in 

Figure 3

. Tighten all nuts, screws, 

and studs to 40 inch-lbs (4.5 Nm) of torque. 

5. Use a #6 AWG copper wire to connect the cabinet to an approved earth ground source as 

specified by local code or practice. Avoid sharp bends in the ground wire. 

8

 IN

(20.3 CM)

15 IN

(3

8

.1 CM)

30 IN

(76.2 CM)

13 IN

(33.0 CM)

32 IN

(

8

1.3 CM)

BACK

OF

CABINET

23116-A

Summary of Contents for OmniReach FTTX














Reviews: