CommScope OneCell RP Series Installation Manual Download | Manualshive

Page: 4 / 10

background image

3

2

Wrap each clamp around the pole and tighten the clamp screw to secure the RP to
the pole.

3

Insert two screws into the upper holes on opposite sides of the RP as shown in the
drawing below.

Insert screws
into the holes
called out – one
on each side.

«
...
2
3
4
5
6
...
»

Summary of Contents for OneCell RP Series











Reviews:

No comments

Related manuals for OneCell RP Series

Brand: Aastra Pages: 30

Brand: Rane Pages: 14

Brand: Panasonic Pages: 1

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 20

IntelliGate 2025

Brand: Aastra Pages: 71

Aura Communication Manager Branch i120

Brand: Avaya Pages: 24

BeoSound 3000 2671

Brand: Bang & Olufsen Pages: 68

Brand: 2VV Pages: 29

Brand: Danfoss Pages: 8

Ostrich Eggbot 2.0

Brand: Evil Mad Scientist Pages: 45

Brand: Lutron Electronics Pages: 36

Brand: Blaupunkt Pages: 13

RS2135I - Compact Audio System

Brand: RCA Pages: 13

Brand: RCA Pages: 19

Brand: RCA Pages: 21

Stealthbox SB-F-150-SCDBL/12TW3

Brand: JL Audio Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands