3
Professionally Installed Products
The product is to be installed according to the installation instructions. The Use/Operator does not have access to the device once the
device is installed and in use. Provisions for permanent grounding is provided.
1. Installation personal: This product is designed for specific application and needs to be installed by a qualified personal who has RF and
related rule knowledge. The general user shall not attempt to install or change the setting.
2. Installation location: The product shall be installed at a location where the radiating antenna can be kept 20 cm from nearby person in
normal operation condition to meet regulatory RF exposure requirement
3. External antenna: Use only the antennas which have been approved by Ruckus Wireless. The non-approved antenna(s) may produce
unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC limit and is prohibited.
4.
Installation procedure: Please refer to user’s manual for the detail.
5. Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in
US Rule CFR 47 part 15 section 15.247 & 15.407. The violation of the rule could lead to serious federal penalty.
Products intended to be powered by an external power supply:
Caution
–
This product is intended to be supplied by a Listed Direct Plug-In Power Unit marked Class 2 or LPS (sub-clause 2.5 of standard
EN 60950-1). Available Ruckus power supplies intended for product operation are identified in the product datasheet. The last two digits
of the power supply part number represent the country code. For additional applicable power supplies/options, see user instructions and
product datasheet.
Medical Statement
Ruckus Wireless Access Points shall only be used in ME systems where the intended EM ENVIRONMENT does NOT does not rely on the
WLAN radio link for BASIC SAFETY or ESSENTIAL PERFORMANCE of the ME SYSTEM.
Australia and New Zealand Statement
This device complies with the ACMA requirements for a WiFi device namely Radiocommunications (Short Range Devices) 2014 and
Radiocommunications (Compliance Labelling
–
Devices) Notice 2014 and the New Zealand Radiocommunications Regulations (General
User Radio Licence for Short-Range Devices). The equipment complies with the ACMA and New Zealand requirements for radiation
exposure for a “general user/non
-
aware user”. This equipment should be installed and operated with a minimum distance of 20 cm
between the radiator and your body. This equipment complies with the Australian and New Zealand safety requirements and should only
be used with the specified power adapter carrying a RCM mark and Electrical Approval No.
Brazil Statement
For Brazil, those products are designed for specific application and needs to be installed by a qualified personal who has RF and related
rule knowledge. Regarding the operation on range of 5150 MHz to 5350 MHz, the average output power of the equipment must be
adjusted to the maximum limit of - 0,48 dBm and for 5470 MHz to 5725 MHz, the average output power of the equipment must be adjusted
to the maximum limit of 6,44 dBm.
Para o Brasil, esses produtos são projetados para aplicações específicas e necessidades a serem instalados por um pessoal qualificado
que tenha conhecimento regra RF e afins.Em relação à operação em série de 5150 MHz a 5350 MHz, a potência média de saída dos
equipamentos deve ser ajustado para o limite máximo de - 0,48 dBm e para 5470 MHz a 5725 MHz, a potência média de saída dos
equipamentos deve ser ajustada ao limite máximo de 6,44 dBm.
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente
autorizados.
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do
mesmo tipo, e não pode causa interferência a sistemas operando em caráter primário
Nigeria Statement
Connection and use of this communications equipment is permitted by the Nigerian Communications Commission
Thailand Statement
This telecommunication equipment conforms to NTC technical requirement
Hong Kong Statement
The 5.15
–
5.35 GHz band shall be restricted to indoor operations only. Obey local regulations when using this product.
Taiwan Statement
使用此
產
品時應避免影響附近雷達系統之操作
This product should not affect the operation of nearby radar systems.
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法
通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾
.
The control, adjustment and on/off operation of this device does not violate the “Administrative regulations on low power rad
io waves
radiated devices”. Any adjustments to the device should be carried out or be monitored by a specialist who has expertise o
n radio
frequency devices. Replacement of components which may lead to the violation to the regulations is not allowed. Without permission
granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original
characteristic as well as performance to an approved low power radio-frequency devices. The low power radio-frequency device shall not
influence aircraft security and interfere with legal communications; if found, the user shall cease operating immediately until no
interference is achieved. The said legal communications means radio communications is operated in compliance with the
Telecommunications Act. The low power radio-frequency devices must not be susceptible with the interference from legal communications
or ISM radio wave radiated devices.
