background image

CO

M

P5

191

Distributed by  

Companion Brands

 

Bundoora Victoria 3083 

www.companionbrands.com.au

SPECIFICATIONS

Part No.

PRI2223

Gas jet size

0.58mm +/- 0.01

Gas consumption

524g/hr - 26.4Mj/hr Per Burner

BTU output

25,000 BTU - Per Burner

Dimensions

590L x 280W x 110Hmm

Weight

5.4kg

Certificate number

GSCS20148

TECHNICAL DETAILS

CARE INSTRUCTIONS

Using warm soapy water with a mild detergent wipe down all surfaces and areas of the appliance, taking care not to allow 
water to enter the burner outlets or aeration holes located in the burner tube. 

DO NOT

 submerge the appliance in a sink or bowl. 

DO NOT

 use abrasive cleaners or bleach. 

MAINTENANCE AND SERVICE

During operation if it is noted that the burner flame is unstable, is changing colour from blue to yellow or has a distinct 
smell it is important that you take the appliance to your local authorised gas appliance repairer for inspection. 
Periodically check the gas control is tight and has no leaks, follow the testing for leaks procedure. Check the gas 
connection and regulator for any signs of wear or damage, if identified contact customer service for a replacement 
assembly immediately. 
For further information or assistance please contact customer service on 1300 555 197 or  
email service@companionbrands.com.au

Summary of Contents for PRI2223









Reviews: