background image

ASSEMBLY MANUAL AND SETUP GUIDE

CAPRICORN 54 EP RTR SPECIFICATIONS AND FEATuRES

Before beginning assembly of your new Compass Boat Models Marlin EP RTR, please read and understand the warnings 
listed on the next page. Failure to do so could lead to bodily harm and/or injury.

The Compass Boat Models Marlin EP RTR is not intended for persons under 14 years of age, unless closely supervised by 
an adult.

All Contents Copyright © 2006, Compass Boat Models Version  August 2006

540-Size Closed End-Bell Electric Motor
6-Cell 800mAH Ni-Cd Battery
AC Slow Charger
Large Wing Provides Ample Downforce for Sharp Steering Control
Easy-Access Radio Compartment
Replacement Parts Readily Available






Hull Type: Shallow "V"
Overall Length: 30 Inches (762mm)
Overall Width: 7 Inches (78mm)
Completely Built and Ready-to-Run
2-Channel FM Radio Control System
Proportional Motor Controller (ESC)






Compass Boat Models,

P.O. Box No. 402,

Texaco Road PO,

New Territories,

Hong Kong.

Made in China

KIT NUMBER CBM0003

MARLIN EP RTR SPECIFICATIONS AND FEATuRES

EXCITEMENT IN THE WATER! 

You'll be on the water and racing full speed in no time, because the Marlin 

comes out of the box Ready For Fun! The radio and all electronics are 
factory installed, so the only thing you have to do is charge and install 
the  battery  (charger  and  battery  are  included).  This  30"  long  boat 

comes  with  a  powerful  540  motor  and  a  6-cell  7.2V  battery,  which 

provides outstanding performance in large pools, lakes and ponds.

EXCITEMENT IN THE WATER! 

You'll be on the water and racing full speed in no time, because the Marlin 

comes out of the box Ready For Fun! The radio and all electronics are 
factory installed, so the only thing you have to do is charge and install 
the  battery  (charger  and  battery  are  included).  This  30"  long  boat 

comes  with  a  powerful  540  motor  and  a  6-cell  7.2V  battery,  which 

provides outstanding performance in large pools, lakes and ponds.

Summary of Contents for Marlin Cruiser CBM0003













Reviews: