background image

31

COMUNELLO

  ®Copyright 2016 - All rights reserved

ENGLISH

ANT-:   

Antenna Ground Input.

ANT+:   

Antenna Hot pole input.

CN3:

ENC1 +:  

Operator 1 Encoder Power Input

ENC1 E: 

Operator 1 Encoder Signal Input

ENC1 GND: 

Common GND input

MOT1 FCA: 

Operator 1 Opening Limit Switch Input (NC).

MOT1 FCC: 

Operator 1 Closing Limit Switch Input (NC).

SYNC D: 

Master/Slave Synchronisation Input (Data)

SYNC GND:  Master/Slave Synchronisation Input (GND)

CN8:

L:   

 

230 V~ line input (phase).

N:   

 

230 V~ line input (neutral).

•  Connection of the Y power cord.

10.3 FUNCTIONAL CHARACTERISTICS

OPERATION:

When either the remote or the low voltage pushbutton panel are used to 
control the barrier, operation is as follows:
the first command opens the barrier until motor time elapses or the arm 
reaches its opening limit position; the second command closes the barrier; 
if another command is transmitted during the Opening movement, the 
control unit disregards the command; if a command is transmitted during 
the Closing movement the control unit reverses the movement direction.

AUTOMATIC CLOSING:

The control unit can be set up to close the barrier automatically without 
sending any additional commands.
Selection of this type of operation is described in Pause time programming 
mode.

EMERGENCY STOP INPUT:

The control unit allows the connection of an emergency stop pushbutton 
(NC). Pressing this pushbutton irrespective of the current operating mode 
of the control unit will cause barrier movements to stop immediately. An 
additional barrier movement command will be valid, provided the emergency 
stop input is deactivated and, in any case, the control unit will perform the 
barrier opening cycle after preflashing for 5 seconds.
Important: in Master/Slave applications, if you want to stop the Barriers 
simultaneously, the Emergency Stop Inputs of the Master and Slave control 
units must be interconnected.

PHOTOCELLS:

Photocells can be powered by and connected to the control unit in 
accordance with directive EN 12453.
•  Input DS1 (NC)
  Tripping of the photocells during opening is disregarded, while during 

closing it causes reversal of the direction of movement.

•  Input DS2 (NC)
 

Tripping during opening causes momentary stopping of the barrier; once 
the photocell is freed, the control unit resumes the opening movement. 
Tripping during closing causes reversal of the direction of movement.

IMPORTANT:

 in Master/Slave applications tripping of input DS2 causes 

exclusively reversal of the direction of movement in the closing stroke.

OPENING AND CLOSING LIMIT SWITCHES:

The control unit allows the connection of Opening and Closing limit 
switches (NC). Tripping of the limit switches in the associated operating 
cycles causes immediate stopping of barrier movement.

ADJUSTMENT OF MOTOR FORCE DURING THE “NORMAL” CYCLE:

The electronic control unit is equipped with a “SPEED” trimmer for 
adjustment of Motor Force during the Normal cycle. 
Adjustment can be performed in a range of between 50% and 100% of 
maximum force during the Normal cycle.

ADJUSTMENT OF MOTOR FORCE DURING THE “SLOWDOWN” 
CYCLE:

The electronic control unit is equipped with a “SLOWING” trimmer 
adjustment of Motor Force during the Slowdown cycle.
Adjustment can be performed in a range of between 50% and 100% of 
maximum force during the Slowdown cycle.

OBSTACLE DETECTION:

The electronic control unit is equipped with a “SENS” trimmer, completely 

managed by the microprocessor, for adjustment of the opposing Force 
required to detect the presence of an obstacle.

The adjustment can be made with a trip time from a minimum of 0.1 
seconds to a maximum of 1 seconds

IMPORTANT:

 detection of an obstacle always causes a reversal of the 

direction of movement.

MOTOR ENCODER:

The control unit allows connection of an Encoder. The use of Encoders 
facilitates the work of the control unit in the Obstacles Detection function 
and ensures enhanced precision during execution of arm movements.

FLASHING LIGHT:

The control unit features an output to control a 24 V  25W max flashing 
light. Operation of the flashing light depends on the movement of the motor 
and automatic closing, which, if selected, enables the flashing light also 
during the pause time.

INDICATOR LIGHT:

The control unit allows a 24 V  indicator light to be connected to display 
the status of the automation system.
Indicator light off: barrier closed
Indicator light on: barrier open
Indicator light slow blinking: opening movement; rapid blinking: closing 
movement.

OPERATION WITH TIMER:

The control unit allows a timer to be connected in place of the open – close 
pushbutton.
E.g.: at 08.00 am the timer closes the contact and the control unit 
commands an opening movement; at 06.00 pm the timer opens the 
contact and the control unit commands a closing movement. From 08.00 
am – 06.00 pm at the end of the opening cycle the control unit disables the 
flashing light, automatic closing and the remotes.

BUFFER BATTERY:

The control unit is equipped with a built-in 27.4 V  battery charger to 
keep a full charge on the two 12V batteries connected in series. The 
batteries allow the barrier to perform several complete open/close cycles 
in emergency mode. The Flashing Light and LED strip output will operate 
only for the first 4 seconds of the movement when mains power is absent.

CHECKING THE MOTOR DIRECTION OF RUN 
AND MASTER/SLAVE SELECTION

Important Note: make sure the settings of dip-switch SW1 are 
changed with the control unit off and then repeat the control unit 
programming procedure.

The electronic control unit is equipped with a Dip Switch SW1, which can 
be used to change the direction of run of the connected motor without 
having to physically alter the electrical connections (DIP 1). In addition, again 
using (DIP 2) of Dip Switch SW1, in the case of synchronized operation of 
two barriers the control unit can be used to select which one acts as Master 
and which one acts as Slave.

Important Note:

•  In Master/Slave applications synchronised opening of the barrier is 

available using the PUL input or exclusively the master barrier using the 
PED input.

•  In the Slave control unit all the control and safety inputs (except the 

Emergency stop input) are automatically disabled because they are 
managed by the control unit configured as the Master. 

INV

1

ON

2

OFF

MASTER

INV

ON

SLAVE

1

ON

2

SW1

SW1

Summary of Contents for LIMIT 500









































































Reviews: