EN
56
IDV2660
Crackling
This sound appears with cooking utensils consisting of several layers of various
materials. It is caused by vibrations on the connecting areas of individual layers.
The sound depends on the cooking utensil. It may change in dependence on the
quantity and kind of food being cooked in the utensil.
Sound of the fan
For good operation of the electronics it is necessary that it works at a permanently
controlled temperature. That is why the heating plate is equipped with a fan
which can be set to various power levels according to the measured temperature.
The fan may work even after the switch-off of the heating plate, if the measured
temperature is still too high.
ENVIRONMENTAL PROTECTION
• Packaging materials and obsolete appliances should be recycled.
• The transport box may be disposed of as sorted waste.
• Polyethylene bags shall be handed over for recycling.
Appliance recycling at the end of its service life:
A symbol on the product or its packaging indicates that this product should not go into household waste.
It must be taken to the collection point of an electric and electronic equipment recycling facility. By making
sure this product is disposed of properly, you will help prevent the negative effects on the environment and
human health that would otherwise result from inappropriate disposal of this product. You can learn more
about recycling this product from your local authorities, a household waste disposal service or in the shop
where you bought this product.
SERVICING
Any extensive maintenance or repair that requires access to the inner parts of the product must be performed by an expert
service centre.
EN
55
IDV2660
After fixation of the ends of the wires under the heads of the screws in the terminal box insert the cable in the terminal
box and secure it with a clip against pulling out.
After the connection turn the unit into the working position, put it in the cut-out and check the position of the supply
cable.
Operation sounds of the unit
The induction heating technology is based on specific parameters of metal materials, when under the influence of high-
frequency waves. Under special circumstances these vibrations can manifest themselves by weak sounds, which do not
signal any fault. These include:
Deep hum such as at
a transformer
This sound accompanies cooking at high power level. It is caused by big amount of
energy which is transferred from the heating plate to the cooking utensil. This sound
will disappear or weaken as soon as the hotzone is switched over to lower power.
Beeping
This sound usually appears in the case of an empty cooking utensil. It will disappear
when you pour water or put food in the utensil.
High beeping sounds
These sounds appear mainly with cooking utensils consisting of several layers of
various materials, when they are in operation at the maximum heating power. This
effect does not influence the result of cooking. The beeping disappears or weakens
as soon as the power is reduced.
TROUBLESHOOTING
Problem
Cause, solution
The household wiring protection
reacts to the switching on of the
heating plate.
Check that the input of all switched-on units does not exceed the maximum load of
the household wiring. Check whether the protection breaks in case of switching on
of another hotzone too.
The heating plate has switched
off.
Somebody has touched the main switch accidentally. Switch on the heating plate
again. Perform setting once more.
When you put a utensil on the
induction hotzone, the „
U
“
symbol is displayed (and the
hotzone does not heat).
Check whether the cooking utensil is electromagnetic (i.e. whether it attracts
a magnet). Check whether the bottom diameter of the utensil is sufficient.
If the cooking utensil has got too hot during use, let it cool down.
If the indicator does not shine even after the next switching off and on again,
disconnect the heating plate from the mains. Wait 20 seconds and then connect it
again.
Displayed code F0, F1, F2
Cooling fan defect. Contact an authorized service centre.
Displayed code F3-F8
Temperature sensor defect. Contact an authorized service centre.
Displayed code E1, E2,
Incorrect voltage. Check the supply voltage.
Displayed code E3, E4,
Too high temperature. Check the type of used utensil.
Displayed code E5, E6,
Overheated hotzone. Let it cool down before the next use.
EN
58
IDV2560wh | IDV2660n
Summary of Contents for IDV 2660n
Page 2: ...ID D c P k O T D P P N T T Č I Ř S O P C V v ř 1 N t 2 J 3 V n s j P p P T s p P m ...
Page 61: ......
Page 62: ......
Page 63: ......
