CONTROL PANEL DESCRIPTION
1
Lighting On/Off button
2
Minus (-) button
3
Display
4
Plus (+) button
5
Appliance On/Off button
1
2
3
4
5
DESCRIPTION OF CONTROL PANEL BUTTONS
Lighting On/Off button
• Push the button to switch on/off the appliance lighting.
Minus (-) button
• Push the button to decrease extracted air exhaust output.
• When pushed, the button illuminates and the display shows the output value (1-3).
• If the output value is 1 and the minus (-) button is pushed, only an audible signal will sound and the dis-
play will show the lowest output value (1).
• You can decrease the extracted air output only when the appliance is switched on.
Display
• The display shows the extracted air exhaust output.
Plus (+) button
• Push the button to increase extracted air exhaust output.
• When pushed, the button illuminates and the display shows the output value (1-3).
• If the output value is 3 and the plus (+) button is pushed, only an audible signal will sound and the display
will show the highest output value (3).
• You can increase the extracted air output only when the appliance is switched on.
Appliance On/Off button
• Push the button to switch on/off the appliance.
• When pushed, the button illuminates.
• Upon switching the appliance on, the extracted air output is set to the lowest output value (1). This value is
shown on the display.
• Whenever the appliance is switched on, the extracted air output shall always be set to the lowest output
value (1).
• If you push the On/Off button when the appliance is switched on, the extracted air output shall decrease
to the lowest output value (1) and the delayed switching-off shall take place after 3 minutes. The lowest
output value (1) will start to flash on the display.
• The preset time for the delayed switching-off is fixed and cannot be changed.
• During the delayed switching-off, you can switch off the appliance by pushing the On/Off button.
• To switch off the appliance completely, push the On/Off button
twice.
USER'S MANUAL
Before first use
Before first use you should wipe the outside and inside of the appliance with a damp cloth for hygiene
reasons.
Ventilation mode
The extracted air is discharged through the flexible outlet duct to the ventilation shaft out of the room. If the
appliance is equipped with a carbon filter,
remove it
(see chapter Cleaning and maintenance).
1. Push button (1) to switch on the appliance.
2. Using buttons (2) and (4) select the required value of the extracted air exhaust output.
3. The display shows the output value (1-3).
4. Push button (1)
twice
to switch the appliance off.
Recirculation mode
If there is no possibility of discharging the extracted air out of the room, you can use the recirculation mode.
In this case, the extracted air is filtered
through the metal fat filters and the carbon filter
. An active carbon
in this filter absorbs the smell. Air, free from the smell, flows back into the room through openings situated in
the upper chimney cover. When the recirculation mode is used,
it is necessary to purchase and install
the
appropriate carbon filters (see chapter Cleaning and maintenance).
1. Push button (1) to switch on the appliance.
2. Using buttons (2) and (4) select the required value of the extracted air exhaust output.
3. The display shows the output value (1-3).
4. Push button (1)
twice
to switch the appliance off.
Note:
When the recirculation mode is used (carbon filter installed), the extracted air output can drop.
CLEANING AND MAINTENANCE
• Disconnect the power cord from the wall outlet or switch off the circuit breaker of the appliance before
cleaning and maintenance.
• To clean the appliance outside, use a damp cloth, a soft brush or a fine sponge, and then wipe it dry.
• Do not use coarse abrasive cleaning agents or sharp metal scrapers for cleaning of the appliance as this
could result in surface scoring.
• Do not use steam jets to clean the appliance!
• Never leave aggressive or acidic substances (lemon juice, vinegar) on enamelled or stainless parts of the
appliance.
EN
EN
55
54
OPK 4660
OPK 4660
