Concept2 VT 7010 Manual Download

Page: 47 / 118

OPERATING INSTRUCTIONS

1. Place the unit on a stable surface or floor to prevent it from tipping over. Remove the entire feed cord from the

storage space and uncoil it.

2. Connect the power cord plug to the wall outlet.

3. Select the required function using the mode selector:
0 = Off

= Cool air

  = 50% heating capacity (1,000 W)
  = Full heating capacity (approximately 2,000 W)
4. You may set the required temperature in the room using the thermostat regulator. When heating function

or is selected, the unit will alternately switch on and off, thus keeping the required temperature.

Note:

A more accurate temperature can be set as follows:

Set the thermostat to the maximum, and switch the heating to or . When the required temperature has

been reached in the room, turn the thermostat slowly to a lower temperature, until the unit switches off.

If you use the fan in the cool air mode , set the thermostat regulator to the maximum.
5. After use, move the mode selector to the 0 position and unplug the unit from the mains.

VT6930

MAINTENANCE AND CLEANING

Warning!

Before cleaning the unit, always disconnect the power cord from the wall outlet!
Prior to handling, make sure the unit has cooled down!

The surface of the unit may only be cleaned using a wet cloth. Do not use any detergents or hard objects, as they may

damage the unit’s surface!
The air inlet and outlet grilles should be cleaned frequently to ensure proper operation of the unit and to avoid

overheating.
Dust accumulated in the unit may be blown out or removed by a vacuum cleaner.

Never clean the unit under running water, do not rinse it, and do not submerge it in water!

TROUBLESHOOTING

The unit is equipped with a safety fuse that cuts off the power supply to the heater, and restores it after it cools down.
If this happens in the course of ordinary operation, check the cleanliness of the inlet and outlet grilles, or change

location of the unit to improve the air circulation in and around the unit.

Caution

When turning the unit on for the first time or after a prolonged downtime the unit may emit a slight odour. This odour

will vanish after a short time.

Note: Do not use the unit in rooms smaller than 4 m

1. Place the unit on a stable surface or floor to prevent it from tipping over. Remove the entire feed cord from the

storage space and uncoil it.

2. Connect the power cord plug to the wall outlet.
3. Select the required function using the mode selector:

4. You may set the required temperature in the room using the thermostat regulator. When heating function (

) or

(

) is selected, the unit will alternately switch on and off, thus keeping the required temperature.

Note:

A more accurate temperature can be set as follows:

Set the thermostat to the maximum, and switch the heating to (

) or (

) . When the required temperature

has been reached in the room, turn the thermostat slowly to a lower temperature, until the unit switches off.
If you use the fan in the cool air mode , set the thermostat regulator to the maximum.

5. After use, move the mode selector to the (

) position and unplug the unit from the mains.

= Off
= Cool air

= 50% heating capacity (750 W )

= Full heating capacity (approximately 1500 W ).

VT 7010

OPERATING INSTRUCTIONS

1. Place the unit on a stable surface or floor to prevent it from tipping over. Remove the entire feed cord from the

storage space and uncoil it.

2. Connect the power cord plug to the wall outlet.

3. Select the required function using the mode selector:
0 = Off

= Cool air

  = 50% heating capacity (1,000 W)
  = Full heating capacity (approximately 2,000 W)
4. You may set the required temperature in the room using the thermostat regulator. When heating function

or is selected, the unit will alternately switch on and off, thus keeping the required temperature.

Note:

A more accurate temperature can be set as follows:

Set the thermostat to the maximum, and switch the heating to or . When the required temperature has

been reached in the room, turn the thermostat slowly to a lower temperature, until the unit switches off.

If you use the fan in the cool air mode , set the thermostat regulator to the maximum.
5. After use, move the mode selector to the 0 position and unplug the unit from the mains.

VT6930

MAINTENANCE AND CLEANING

Warning!

Before cleaning the unit, always disconnect the power cord from the wall outlet!
Prior to handling, make sure the unit has cooled down!

The surface of the unit may only be cleaned using a wet cloth. Do not use any detergents or hard objects, as they may

damage the unit’s surface!
The air inlet and outlet grilles should be cleaned frequently to ensure proper operation of the unit and to avoid

overheating.
Dust accumulated in the unit may be blown out or removed by a vacuum cleaner.

Never clean the unit under running water, do not rinse it, and do not submerge it in water!

TROUBLESHOOTING

location of the unit to improve the air circulation in and around the unit.

Caution

When turning the unit on for the first time or after a prolonged downtime the unit may emit a slight odour. This odour

will vanish after a short time.

Note: Do not use the unit in rooms smaller than 4 m

1. Place the unit on a stable surface or floor to prevent it from tipping over. Remove the entire feed cord from the

storage space and uncoil it.

2. Connect the power cord plug to the wall outlet.
3. Select the required function using the mode selector:

4. You may set the required temperature in the room using the thermostat regulator. When heating function (

) or

(

) is selected, the unit will alternately switch on and off, thus keeping the required temperature.

Note:

A more accurate temperature can be set as follows:

Set the thermostat to the maximum, and switch the heating to (

) or (

) . When the required temperature

has been reached in the room, turn the thermostat slowly to a lower temperature, until the unit switches off.
If you use the fan in the cool air mode , set the thermostat regulator to the maximum.

5. After use, move the mode selector to the (

) position and unplug the unit from the mains.

= Off
= Cool air

= 50% heating capacity (750 W )

= Full heating capacity (approximately 1500 W ).

VT 7010

VT7010