background image

 

5

 

FCC Warnings 

 
This equipment generates or uses radio frequency energy. Changes or modifications to 
this equipment may cause harmful interference unless the modifications are expressly 
approved in the instruction manual. The user could lose the authority to operate this 
equipment if an unauthorized change or modification is made. 
 
This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. 
 
This equipment generates, uses and can generate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that the interference will not occur 
in a particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following 
measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment to an outlet on a circuit different from that to which the 
receiver is connected. 

 

Consult the dealer for technical assistance.

 

 

 

 

Other Warnings 

 
Electronic devices such as pacemakers, medical equipment, and navigation equipment on 
an airplane are susceptible to the energy generated from radios such as the CS1000 if 
they are not adequately shielded. 

 

If there are signs posted in a hospital or some other health facility that says not to use 
radios or cell phones, turn off your radio because they might interfere with the 
sensitive medical equipment. 

 

If you are on board an aircraft it is recommended you not use this product because of 
the potential to interfere with the aircraft navigation systems and other electronics on 
board. Failure to do so without the express permission of the crew could cause you to 
be detained by the FBI when you disembark from the plane. It also has the potential 
to cause the plane to crash.

 

 
 
 

Summary of Contents for CS1000

















Reviews: