background image

 

M.2 GPS  

Users Guide 

www.connecttech.com

 

 

Document: CTIM-000454 

Revision: 0.01 

 

 

Page 12 of 13 

Date: 2021-03-01 

 

Software Support for the NEO-7 and NEO-M8 GPS Receivers 

The USB drivers for the NEO-7 and NEO-M8 GPS Receivers can be found on the u-Blox website: 

https://www.u-blox.com/en/product-

resources?f[0]=property_file_product_filter%3A2668&f[1]=field_file_category%3A221

 

 

For configuration and setting options for the NEO-7 GPS receiver, please refer to the u-Blox 7 Receiver 

Description Including Protocol Specification V14 found on the u-Blox website: 

https://www.u-blox.com/en/product-resources?f[0]=field_file_category%3A209

 

 

For configuration and setting options for the NEO-M8N GPS receiver, please refer to the u-Blox M8 

Receiver Description Including Protocol Specification found on the u-Blox website: 

https://www.u-blox.com/en/product-resources?f[0]=field_file_category%3A209

 

 

Changing the configuring of the NEO modules is best accomplished using the u-center application 

provided by u-Blox. To get the u-center application for windows, please see the link below: 

https://www.u-blox.com/en/product/u-center-windows

 

 
 

 

Summary of Contents for M.2 GPS














Reviews: