background image

 

M.2 GPS  

Users Guide 

www.connecttech.com

 

 

Document: CTIM-000454 

Revision: 0.01 

 

 

Page 3 of 13 

Date: 2021-03-01 

 

PREFACE 

Disclaimer 

The information contained within this user’s guide, including but not limited to any product 

specification, is subject to change without notice. 

 

Connect Tech assumes no liability for any damages incurred directly or indirectly from any technical or 

typographical errors or omissions contained herein or for discrepancies between the product and the 

user’s guide.  

Customer Support Overview 

If you experience difficulties after reading the manual and/or using the product, contact the Connect 

Tech reseller from which you purchased the product. In most cases the reseller can help you with 

product installation and difficulties. 

 

In the event that the reseller is unable to resolve your problem, our highly qualified support staff can 

assist you.  Our support section is available 24 hours a day, 7 days a week on our website at: 

https://connecttech.com/support/resource-center/. See the contact information section below for 

more information on how to contact us directly. Our technical support is always free. 

 

Contact Information 

Contact Information 

Mail/Courier 

Connect Tech Inc. 

Technical Support 

42 Arrow Road 

Guelph, Ontario 

Canada N1K 1S6 

Contact Information 

sales@connecttech.com

 

support@connecttech.com

 

www.connecttech.com

 

 

Toll Free: 

800-426-8979 (North America only) 

Telephone: 

+1-519-836-1291 

Facsimile: 

519-836-4878 (on-line 24 hours) 

Support 

Please go to the Connect Tech Resource Center for product manuals, 

installation guides, device drivers, BSPs and technical tips.  

 

Submit your technical support questions to our support engineers. 

Technical Support representatives are available Monday through Friday, 

from 8:30 a.m. to 5:00 p.m. Eastern Standard Time. 

Summary of Contents for M.2 GPS














Reviews: