Connect Tech M.2 GPS User Manual Download

Page: 9 / 13

M.2 GPS

Users Guide

www.connecttech.com

Document: CTIM-000454

Revision: 0.01

Page 9 of 13

Date: 2021-03-01

GND

CONFIG_1

(GND)

+3.3V

GND

+3.3V

External I/O Connector

The pinout for the I/O connector is outlined in the table below.

Function

External I/O Connector

501568-0507

Location

Connector PN 501568-0507 - Manufacturer: Molex

Mating

Connector PN

501330-0500 - Manufacturer: Molex

CTI Cable #: CBG162

Pinout

Pin Signal

Description

1 EXT_INT /

WHEELTICK

External Interrupt Input or

Speed pulse input

2 TIMEPULSE Time pulse Output
3 FWD

Forward/Reverse indicator

4 GND

Digital Ground

5 EXT_BAT

External Battery Input

NOTE: WHEELTICK is only available on M2G205 and M2G206, otherwise this signal is EXT_INT

NOTE: FWD is only available on M2G205 and M2G206, otherwise it is not connected and should be left floating

Active Antenna Connector

Function

Active Antenna Connector

HSC - MHF4 Jack

Location

Connector PN

MM4829-2702RA4 - Manufacturer: Murata

Mating Connector

HSC – MHF4 Socket Standard

CTI Cable #: CBG214

Summary of Contents for M.2 GPS














Search results

Summary of Contents for M.2 GPS

Reviews:

Related manuals for M.2 GPS

Brands by name

Popular brands

Connect Tech M.2 GPS, User Manual

Search results

Summary of Contents for M.2 GPS

Reviews:

Related manuals for M.2 GPS

Brands by name

Popular brands