PREPARATION OF MACHINE
HANDLING THE PACKAGED MACHINE
The machine's overall weight including packaging is 535Kg.
N.B.
: it is recommended that all the packaging components be kept for any future machine
transportation.
DANGER
: move the packaged product with handling equipment that complies with legal
requirements regarding size and mass of the packaging.
A
1605
B
1280
C
2030
HOW TO UNPACK THE MACHINE
The machine is shipped in specific packaging. To remove it, proceed as follows:
1.
Place the lower part of the outer packaging in contact with the floor.
N.B.
: use the pictograms printed on the box as a reference.
2. Remove the outer package.
WARNING
: the machine is contained in specific packaging materials, whose elements (plastic
bags, staples, etc.) can pose potential hazards, and must not be left within reach of children,
disabled persons, etc.
3. Remove the boxes containing the disc brushes and squeegee body from the machine.
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. At the rear of the machine position the three ramps present in the package.
ATTENTION:
the three ramps should be positioned so they are centred with the wheels of the
machine, so that the machine is not damaged during its descent.
5.
The machine is fixed to the pallet with wedges (1) that block the wheels (
Fig.1
). Remove these
wedges.
6. Check that the main switch on the control panel has been set to “0”. If this is not the case, turn
the key (2) a quarter turn anti-clockwise (
Fig.2
). Remove the key from the main switch.
7. Grip the back of the seat (3) and turn the seat support plate to its maintenance position (
Fig.3
).
ATTENTION
: to prevent the seat from rotating, insert the retainer (4) into the slot (5) (
Fig.4
).
8. Connect the backup battery carriage's connector to the machine's main system connector
(
Fig.5
).
9. Grip the back of the seat (3) and turn the seat support plate to the working position.
NB
: before rotating the seat support plate, remove the retainer (4).
10. Sit on the driver’s seat.
11. Insert the key (2) into the main switch on the control panel. Set the main switch to “I”, turn the key
a quarter turn clockwise (
Fig.6
).
2
3
1
1
2
3
OFF
6
2
ON
4
4
5
5
12. Turn the brush head control level (6) anti-clockwise (
Fig.7
); in this way the brush head body will
be raised off the pallet.
13. Turn the squeegee control lever (7) clockwise (
Fig.8
) to raise the squeegee body off the pallet.
14. Engage the reverse gear using the reverse gear activation - deactivation lever (8) (
Fig.9
).
15. Press the drive pedal (9) (
Fig.10
) to begin moving the machine.
16. Drive the machine down the ramp.
ATTENTION
: during this operation, check there are no people or objects near the machine.
17. Set the main machine switch to “0” (
Fig.2
). Remove the key from the main switch.
18.
Get off the machine.
CAUTION
: when getting down from the machine, do not place your foot on the scrubbing brush
head or side brush head brush.
19. Grip the back of the seat (3) and turn the seat support plate to the maintenance position.
20. Grip the handle (4) and lift the recovery tank to its maintenance position.
21. Disconnect the backup battery carriage connector from the main machine system connector.
22. Grip the handle (4) and lower the recovery tank to its working position.
23. Grip the back of the seat (3) and turn the seat support plate to the working position.
24.
For reasons of packaging, the brushes are supplied not fitted on the machine, to fit them to the
brush head body read the paragraph “
FITTING THE BRUSH HEAD BRUSHES
”.
25.
For reasons of packaging, the splash guard s are supplied not fitted on the machine, to fit
them to the brush head body read the paragraph “
FITTING THE BRUSH HEAD BODY SIDE
”.
26. For reasons of packaging, if the machine version provides for it, the side brush is supplied not
fitted on the machine, to fit it to the side brush head body read the paragraph “
”.
7
8
6
7
9
8
10
9
HOW TO MOVE THE MACHINE
To transport the machine safely, proceed as follows:
DANGER
: before starting any task, make sure the current regulations concerning the safe
transport of dangerous substances are scrupulously observed.
1. Check to make sure that the solution tank and the recovery tank are empty. If this is not the case,
empty them (see the sections titled “
” and “
”).
2. Sit on the driver’s seat.
3. Insert the key (1) into the main switch on the control panel. Bring the main switch to its "I" position
by turning the key (1) a quarter turn clockwise (
Fig.1
).
4. Turn the brush head control lever (2) anti-clockwise (
Fig.2
); in this manner the brush head body
will be raised off the floor.
5. Turn the squeegee control lever (3) clockwise (
Fig.3
) to raise the squeegee body off the floor.
6. Press the drive pedal (4) (
Fig.4
) to begin moving the machine.
7. Use a ramp to move the machine up onto the transport vehicle.
CAUTION
: during this operation, check there are no people or objects near the machine.
N.B.
: the ramp gradient must not be such as to cause damage to the machine as it goes up.
8. Position the machine on the means of transport, and set the main switch to “0” by turning the key
(1) a quarter turn anti-clockwise (
Fig.5
). Remove the key from the main switch.
9.
Get off the machine.
CAUTION
: when getting down from the machine, do not place your foot on the scrubbing brush
head or side brush head brush.
3
2
1
1
2
3
ON
15
Braking system oil level check label:
Located near the braking system oil basin, to remind the operator to check the
level of oil in the basin.
The bottom part of the label shows the recommended oil for the braking system.
1
1
1
2
2
3
3
4
4
Vacuum wand optional accessories kit position label:
Applied above the recovery tank cover to identify and position the accessories of
the vacuum wand optional kit.
