CLEANING THE BRUSH HEAD BRUSHES (SWEEPING VERSION)
Careful cleaning of the brush guarantees better cleaning of the floor as well as a longer brush head gear
motor lifespan. To clean the brush, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
”).
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Open the machine's left lateral carter (1) (
Fig.1
).
4. With the brush head in its raised position, turn the knobs (2) that hold the left lateral carter (3) in
place anti-clockwise (
Fig.2
).
5. Remove the left lateral carter (3) (
Fig.3
).
6. Extract the brush from inside the tunnel (
Fig.4
). Clean the brush under a stream of running water
to remove any impurities from its bristles. Check the bristles. If they are excessively worn, replace
the brushes (the bristles should protrude by at least 10mm). For replacing the brushes, refer to
“
FITTING THE BRUSH HEAD BRUSHES
”.
7. After checking to make sure that the brush is clean, reassemble it and move on to the one at the
rear.
NB
: you are advised to invert the right and left-hand brushes every day.
ATTENTION
: If the brushes are not new, and have deformed bristles, it is better to reassemble
them in the same position in order to prevent the different inclination of the bristles from
overloading the brush motor, as well as to prevent excessive vibrations.
To clean the brush with the spray gun kit, proceed as follows:
1. Take the machine to the maintenance area.
2. Check that the brush head body is in its rest position. If this is not the case, turn the brush head
control lever (1) anticlockwise (
Fig.1
) so that the brush head body lifts up off the floor.
3. Check that the squeegee body is in its rest position. If this is not the case, turn the squeegee
head control lever (1) clockwise (
Fig.2
), so that the squeegee head body lifts up off the floor.
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Go to the front of the machine.
5. Open the machine's left lateral carter (3) (
Fig.3
).
6. With the brush head in its raised position, turn the knobs (4) that hold the left lateral casing (5) in
place anti-clockwise (
Fig.4
).
7. Remove the left lateral carter (5) (
Fig.5
).
8. Extract the brush from inside the tunnel (
Fig.6
).
9. Release the tank cleaning accessory (6), at the back of the machine, from the retainers (
Fig.7
).
10. Activate the optional tank cleaning kit ON/OFF pump by pressing the button (7) on the steering
column of the machine (
Fig.8
).
CAUTION
: when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
2
3
1
2
3
3
1
4
3
1
2
3
1
2
5
4
5
6
4
5
NB
: Before starting the optional tank cleaning kit, check the level indicator (8) to see how much
solution there is in the solution tank (
Fig.9
).
11. Activate the solution jet by pressing the lever in the tank cleaning accessory.
NB
: To adjust the solution jet from the
tank cleaning accessory, turn the knob (9) on the
accessory itself
(
Fig.10
).
NB
: To adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob
(10) on the accessory itself
(
Fig.11
).
NB
: To stop the solution jet,
use the lever (11) on the tank cleaning accessory
(
Fig.12
).
12. Clean the brush under running water to remove any impurities from its bristles. Check that the
bristles are not worn; in the event of excessive wear, replace the brush (the bristles should be
at least 10 mm long). Read the paragraph “
” for replacing
the brush.
13. After checking to make sure that the brush is clean, reassemble it and move on to the one at the
rear.
ATTENTION
: the place designated for this operation must comply with current environmental
protection regulations.
7
6
8
7
9
8
12
11
11
10
10
9
CLEANING THE LATERAL BRUSH (SCRUBBING VERSION)
Careful cleaning of the brush guarantees better cleaning of the floor as well as a longer brush head gear
motor lifespan. To clean the brush, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Open the machine's right later carter (1) (
Fig.1
).
4. Move the brush release lever downwards (2) (
Fig.2
).
5. Remove the brush from the lateral brush head (
Fig.3
).
6. Clean the brush under a stream of running water to remove any impurities from its bristles. Check
the bristles. If they are excessively worn, replace the brushes (the bristles should protrude by at
least 10mm). Read the paragraph “
7. After checking to make sure that the brush is clean, reassemble it.
To clean the brush with the spray gun kit, proceed as follows:
1. Take the machine to the maintenance area.
2. Check that the brush head body is in its rest position. If this is not the case, turn the brush head
control lever (1) anticlockwise (
Fig.1
) so that the brush head body lifts up off the floor.
3. Check that the squeegee body is in its rest position. If this is not the case, turn the squeegee
head control lever (1) clockwise (
Fig.2
), so that the squeegee head body lifts up off the floor.
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Go to the front right of the machine.
5. Open the machine's right side casing (3) (
Fig.3
).
6. Move the brush release lever downwards (4) (
Fig.4
).
7. Remove the brush from the lateral brush head (
Fig.5
).
2
3
1
1
2
3
1
2
1
2
3
26
