background image

• Always use appropriate gloves and protective equipment when handling the detergents

used to clean the floor.

• Do not use the machine as a means of transport.

• Avoid working with the brushes when the machine is standing still, so as not to damage the

floor.

In the event of a fire, use a powder fire extinguisher if possible, and avoid the use of water.

• Do not allow any objects to penetrate into the machine's openings. Do not use the machine

is the openings are obstructed.

• Keep the machine's openings free of any dust, lint, hairs, or any other foreign materials that

could reduce the airflow.

Do not remove or alter any labels affixed to the machine.

• This machine has not been approved for use on public streets or roadways.

• Only use the brushes and pad holders that have been supplied along with the machine

or those specified in the Operator's Manual. The use of other brushes or felt pads could

compromise the machine's safety conditions.

• Before starting to work check that there are no leaks.

• Before starting to work check that all the safety devices have been installed and are working

correctly.

• Take all due precautions so that hair, jewellery, loose clothing do not get entangled in the

machine's moving parts.

• Only use the machine in well-lit areas.

DEACTIVATION OF THE MACHINE

WARNING:

• Always protect the machine against sunlight, rain, and other atmospheric agents, both

while it is stationary and while it is in function. Store the machine in a dry, sheltered place:

this machine is only designed for use under dry conditions, and must not be used or stored

outdoors under humid conditions.

• Do not park the machine near combustible materials, powders, gases or liquids.

Stop the machine on a flat surface.

Switch off the machine and remove the key from the instrument panel.

• If the machine is left unattended, it must be protected from any accidental movements

CAUTION:

• In order to prevent the unauthorised use of the machine, the power supply must be

disconnected: switch the machine off using the main switch (by removing the key from the

block) and disconnect the battery's connector from the electrical system's connector.

ATTENTION:

• The machine must only be stored under temperature conditions ranging from +0 °C to +40

°C. The humidity level must be between 30% and 95%.

MAINTENANCE

DANGER:

• In order to avoid short-circuits when working in the vicinity of electrical components, do the

following: avoid the use of non-insulated tools; do not place or allow metallic objects to fall

8

Summary of Contents for Magna BS 2SL Basic





































Reviews: