The descriptions contained in this document are not binding. The company therefore reserves the
right to make any modifications at any time to elements, details, or accessory supply, as considered
necessary for reasons of improvement or manufacturing/commercial requirements. The reproduction,
even partial, of the text and drawings contained in this document is prohibited by law.
The company reserves the right to make any technical and/or supply modifications. The images
are shown as reference only and are not binding as to the actual design and/or equipment.
SYMBOLS USED IN THE MANUAL
PURPOSE AND CONTENT OF THE MANUAL
The aim of this manual is to provide customers with all the information needed to use the machine
in the safest, most appropriate and most autonomous way. This includes information concerning
technical aspects, safety, operation, downtime, maintenance, spare parts and scrapping. The
operators and qualified technicians must carefully read the instructions in this manual before carrying
out any operations on the machine. If in doubt about the correct interpretation of instructions, contact
your nearest Customer Service Centre to obtain the necessary clarifications.
TARGET GROUP
This manual is written both for operators and for qualified machine maintenance technicians.
Operators must not perform operations that should be carried out by qualified technicians. The
manufacturer is not liable for damages resulting from failure to comply with this veto.
PRESERVATION OF THE USER
The Use and Maintenance Manual must be stored in its special pouch close to the machine, protected
from liquids and anything else that could compromise its legibility.
ON CONSIGNMENT OF THE MACHINE
When the machine is consigned to the customer, an immediate check must be performed to ensure all
the material mentioned in the shipping documents has been received, and also to check the machine
has not suffered damage during transportation. If this is the case, the carrier must ascertain the extent
of the damage at once, informing our customer service office. It is only by prompt action of this type
that the missing material can be obtained, and compensation for damage successfully claimed.
IDENTIFICATION DATA
For technical assistance or to request replacement parts, always give the model, the version and the
serial number (written on the relevant plate).
TECHNICAL DESCRIPTION
The
Magna Basic
is a floor scrubbing machine that's capable of handling a wide variety of floors and
types of dirt thanks to the mechanical action of two or three brushes and the chemical action of a
water-detergent solution. As it advances, it collects the dirt removed, as well as the detergent solution
not absorbed by the flooring itself.
The machine must only be used for this purpose
.
INTENDED USE
This scrubbing machine was designed and built for the cleaning (scrubbing and drying) of smooth,
compact flooring in the commercial, residential and industrial sectors by a qualified operator in proven
safety conditions. The scrubbing machine is not suitable for cleaning rugs or carpet floors. It is only
suitable for use in closed (or at least covered) places.
ATTENTION:
the machine is not suitable for use in the rain, or under water jets.
IT IS FORBIDDEN
to use the machine for picking up dangerous dusts or inflammable liquids
in places with an explosive atmosphere. In addition, it is not suitable as a means of transport
for people or objects.
SAFETY
Operator cooperation is paramount for accident prevention. No accident prevention programme can
be effective without the full cooperation of the person directly responsible for machine operation. The
majority of occupational accidents that happen either in the workplace or whilst moving are caused by
failure to respect the most basic safety rules. An attentive, careful operator is most effective guarantee
against accidents and is fundamental in order to implement any prevention programme.
INTRODUCTORY COMMENT
Any floor scrubbing machine can only work properly and effectively if used correctly and kept in full
working order by performing the maintenance operations described in the attached documentation.
We therefore suggest you read this instruction booklet carefully and read it again whenever difficulties
arise while using the machine. If necessary, remember that our assistance service (organised in
collaboration with our dealers) is always available for advice or direct intervention.
REGULATIONS
All references to forwards and backwards, front and rear, right and left indicated in this manual should
be understood as referring to the operator in a driving position with his hands on the steering wheel.
SERIAL NUMBER PLATE
The serial number plate is located at the rear of the steering column, and indicates the machine's
general characteristics, including its serial number. The serial number is a very important piece
of information and should always be provided together with any request for assistance or when
purchasing spare parts. The serial number plate contains the following:
1. The weight of the batteries used to power the appliance (expressed in Kg).
2. The IP protection rating of the appliance.
3. The gross weight of the appliance (expressed in Kg).
4.
The identification code of the appliance.
5. The serial number of the appliance.
6. The name of the appliance.
7. The nominal power consumed by the appliance (expressed in W).
8. The maximum grade that the appliance can handle during work activities (expressed in %).
9. The year in which the appliance was manufactured.
10. The nominal voltage of the appliance (expressed in V).
11. The commercial name of the appliance and the manufacturer's address.
Design by FIMAP Verona (Italy)
Assembled in FIMAP Verona (Italy)
Via Invalidi del Lavoro, 1 S. Maria di Zevio - Verona - Italy
11
10
9
8
7
6
1
2
3
4
5
11
Symbol of the open book with i:
Indicates the need to consult the instruction manual.
Symbol of the open book:
Tells the operator to read the user manual before using the device.
Covered place symbol:
The operations preceded by this symbol must always be carried out in a dry,
covered area.
Information symbol:
Indicates additional information for the operator, to improve the use of the device.
Warning symbol:
Carefully read the sections preceded by this symbol meticulously following the
instructions indicated for the safety of the operator and the device.
Danger symbol (corrosive substances):
The operator should always wear protective gloves to avoid the risk of serious
injury to the hands caused by corrosive substances.
Danger symbol (battery acid leakage):
Indicates the danger of leaking acid or acid fumes from the batteries while they
are being recharged.
Danger symbol (moving carriages):
Indicates that the packed product should be handled with suitable carriages that
conform to legal requirements.
Mandatory room ventilation symbol:
Informs the operator that the room must be ventilated while the batteries are
being recharged.
Symbol indicating the compulsory use of protective gloves:
Indicates that the operator should always wear protective gloves, to avoid the risk
of serious injury to his hands from sharp objects.
Symbol indicating a treading ban:
Informs the operator that it is forbidden to tread on machine components, as this
could lead to serious injury.
Recycling symbol:
Tells the operator to carry out the operations in compliance with environmental
regulations in force in the place where the appliance is being used.
Disposal symbol:
Carefully read the sections marked with this symbol for disposing of the appliance.
