RECOMMENDED MAINTENANCE OPERATIONS
DRAINING THE RECOVERY TANK
Proceed as follows to empty the recovery tank:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
”).
CAUTION
: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3. Remove the drainage hose of the recovery tank from the clamps; it is located at the rear of the
machine (
Fig.1
).
4. Bend the end of the drainage tube in order to create a choke and prevent the content from coming
out (
Fig.2
), then position the tube on the discharge surface, unscrew the cap, and gradually release
the tube.
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
5. Repeat the operations in reverse order to reassemble all the parts.
2
1
EMPTYING THE DEBRIS HOPPER (SWEEPING VERSION)
The thorough cleaning of the debris hopper ensures better floor cleaning performance. To empty the
debris hopper, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
”).
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Open the machine's left lateral carter (1) (
Fig.1
).
4. Release the debris hopper locking pin (2) (
Fig.2
).
5. Use the handle (3) to extract the debris hopper (
Fig.3
) and empty it.
NB
: the place designated for this operation must comply with current environmental protection
regulations.
6. Clean the inside with a jet of water, and use a brush to remove any residual impurities if necessary.
7. Proceed in the opposite order to reassemble all the parts.
2
3
1
2
1
3
CLEANING THE SQUEEGEE BODY
The careful cleaning of the whole vacuum unit ensures better drying and cleaning of the floor as well
as a longer vacuum motor life. To carry out the cleaning of the squeegee body, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Extract the vacuum hose (1) from the vacuum nozzle on the squeegee body (
Fig.1
).
4. Completely unscrew the knobs (2) in the squeegee body's pre-assembly (
Fig.2
).
5. Remove the squeegee body from the slits in the squeegee connector (
Fig.3
).
6. Thoroughly clean the squeegee body vacuum chamber (4) with a jet of water, and then with a
damp cloth (
Fig.4
).
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
7. Thoroughly clean the squeegee body's rear rubber blade (5) with a jet of water, and then with a
damp cloth (
Fig.5
).
8. Thoroughly clean the squeegee body front rubber blade (6) with a jet of water, and then with a
damp cloth (
Fig.6
).
9. Thoroughly clean the vacuum nozzle with a jet of water, and then with a damp cloth.
10. Proceed in the opposite order to reassemble all the parts.
To clean the squeegee body with the optional spray gun kit, proceed as follows:
1. Take the machine to the maintenance area.
2. Check that the brush head body is in its rest position. If this is not the case, turn the brush head
control lever (1) anticlockwise (
Fig.1
) so that the brush head body lifts up off the floor.
3. Check that the squeegee body is in its rest position. If this is not the case, turn the squeegee
head control lever (1) clockwise (
Fig.2
), so that the squeegee head body lifts up off the floor.
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Extract the vacuum hose (3) from the vacuum nozzle on the squeegee body (
Fig.3
).
5. Completely unscrew the knobs (4) on the squeegee body pre-assembly (
Fig.4
).
6. Remove the squeegee unit from the slits in the squeegee connector (
Fig.5
).
7. Release the tank cleaning accessory (5) (at the back of the machine) from the retainers (
Fig.6
).
8. Activate the optional tank cleaning kit ON/OFF pump by pressing the button (6) on the steering
column of the machine (
Fig.7
).
CAUTION
: when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
N.B.
: Before starting the optional tank cleaning kit, check the level indicator (7) to see how
much solution there is in the solution tank (
Fig.8
).
9. Activate the solution jet by pressing the lever in the tank cleaning accessory. Make sure the jet is
pointing into the tank before pressing the lever.
2
3
1
1
2
6
4
5
3
4
1
2
1
2
3
3
4
4
6
5
5
24
TYPE OF MAINTENANCE
AT THE END OF THE WORK
DAIL
Y
WEEKL
Y
BEFORE A
LONG
PERIOD OF NON- USE
TRANSPORT
DRAINING THE RECOVERY TANK
X
X
X
EMPTYING THE DEBRIS HOPPER (SWEEPING VERSION)
X
CLEANING THE SQUEEGEE BODY
X
X
X
CLEANING THE BRUSH HEAD BRUSHES (SCRUBBING
VERSION)
X
X
CLEANING THE BRUSH HEAD BRUSHES (SWEEPING
VERSION)
X
X
CLEANING THE LATERAL BRUSH (SCRUBBING VERSION)
X
X
CLEANING THE LATERAL BRUSH (SWEEPING VERSION)
X
X
CLEANING THE RECOVERY TANK FILTERS
X
X
CLEANING THE RECOVERY TANK
X
X
EMPTYING THE SOLUTION TANK
X
X
X
CLEANING THE WATER SYSTEM FILTER
X
X
CLEANING THE DEBRIS HOPPER
X
X
CLEANING THE VACUUM TUBE
X
X
